MCP2515-E/ST Microchip Technology, MCP2515-E/ST Datasheet - Page 54
![IC CAN CONTROLLER W/SPI 20TSSOP](/photos/6/81/68121/150-20-tssop_sml.jpg)
MCP2515-E/ST
Manufacturer Part Number
MCP2515-E/ST
Description
IC CAN CONTROLLER W/SPI 20TSSOP
Manufacturer
Microchip Technology
Specifications of MCP2515-E/ST
Package / Case
20-TSSOP
Controller Type
CAN Interface
Interface
SPI
Voltage - Supply
2.7 V ~ 5.5 V
Current - Supply
10mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Product
Controller Area Network (CAN)
Number Of Transceivers
1
Data Rate
1 Mbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Supply Current (max)
10 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Ic Interface Type
SPI
No. Of Tx Buffers
3
No. Of Rx Buffers
2
No. Of Filters
6
No. Of Masks
2
No. Of Interrupts
1
Supply Voltage Range
2.7V To 5.5V
Digital Ic Case Style
TSSOP
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP2515DM-BM - BOARD DEMO FOR MCP2515/51MCP2515DM-PTPLS - BOARD DAUGHTER PICTAIL MCP2515MCP2515DM-PCTL - BOARD DEMO FOR MCP2515DV251001 - KIT DEVELOPMENT CAN MCP2510
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP2515-E/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
MCP2515
FIGURE 8-3:
TABLE 8-1:
DS21801F-page 54
Capacitor values are for design guidance only:
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to
produce acceptable oscillator operation. The user
should test the performance of the oscillator over the
expected V
application.
See the notes following
information.
Mode
HS
Typical Capacitor Values Used:
DD
16.0 MHz
8.0 MHz
and temperature range for the
Freq.
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
74AS04
330 kΩ
16.0 MHz
EXTERNAL SERIES RESONANT CRYSTAL OSCILLATOR CIRCUIT
4.0 MHz
8.0 MHz
Note 1: Duty cycle restrictions must be observed (see
Table 8-2
OSC1
27 pF
22 pF
for additional
0.1 mF
XTAL
OSC2
27 pF
22 pF
74AS04
330 kΩ
TABLE 8-2:
Capacitor values are for design guidance only:
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
are not optimized.
Different capacitor values may be required to
produce acceptable oscillator operation. The user
should test the performance of the oscillator over the
expected V
application.
See the notes following this Table for additional
information.
Note 1:
Type
74AS04
Osc
HS
2:
3:
4:
(1)(4)
While higher capacitance increases the
stability of the oscillator, it also increases
the start-up time.
Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate values of external
components.
R
crystals with low drive level specification.
Always verify oscillator performance over
the V
expected for the application.
DD
S
To Other
Devices
may be required to avoid overdriving
and temperature range for the
Table
DD
20 MHz
Crystal
Freq.
4 MHz
8 MHz
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Crystals Used
and temperature range that is
20.0 MHz
(2)
12-1).
4.0 MHz
8.0 MHz
© 2010 Microchip Technology Inc.
MCP2510
OSC1
Typical Capacitor
27 pF
22 pF
15 pF
(3)
C1
Values Tested:
(1)
:
27 pF
22 pF
15 pF
C2