USBN9603-28M/NOPB National Semiconductor, USBN9603-28M/NOPB Datasheet - Page 19

• Manufacturer Part Number: USBN9603-28M/NOPB
• Description: IC CONTROLLER USB 28-SOIC
• Manufacturer: National Semiconductor

Specifications of USBN9603-28M/NOPB

• Controller Type: USB 2.0 Controller
• Interface: Parallel/Serial
• Voltage - Supply: 3 V ~ 5.5 V
• Current - Supply: 30mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (7.5mm Width)
• Usb Type: Node Controller
• Usb Version: 1.1
• No. Of Ports: 2
• Supply Voltage Range: 3V To 5.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: SOIC
• No. Of Pins: 28
• Rohs Compliant: Yes
• For Use With: USBN9604-HS-EB - KIT NODE CONTROLLER SAMPLE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *USBN9603-28M; *USBN9603-28M/NOPB; USBN9603-28M

5.0 MICROWIRE/PLUS Interface
The MICROWIRE/PLUS interface allows the device to function as a CPU or microcontroller peripheral via a serial interface.
This mode is selected by pulling the MODE1 pin high and the MODE0 pin low. The MICROWIRE/PLUS mode uses the chip
select (CS), serial clock (SK), serial data in (SI) and serial data out (SO) pins, as shown in Figure 14.
5.1 OPERATING COMMANDS
The MICROWIRE/PLUS interface is enabled by a falling edge of CS and reset with a rising edge of CS. Data on SI is shifted
in after the rising edge of SK. Data is shifted out on SO after the falling edge of SK. Data is transferred from/to the Shift
register after the falling edge of the eighth SK clock. Data is transferred with the most significant bit first. Table 2 summarizes
the available commands (CMD) for the MICROWIRE/PLUS interface.
Note: A write operation to any register always reads the contents of the register after the write has occurred, and shifts out
that data in the next cycle. This read does not clear the bit in the respective registers, even for a Clear on Read (CoR) type
bit, with one exception: writing to the TXDx (transmit data) registers, which causes undefined data to be read during the next
cycle.
SK
CS
SO
SI
CMD
1 0 5
0 0
0 1
1 0
1 1
Byte Transferred
SYNC
(normal write)
4
(burst write)
1. 1 cycle = 8 SK clocks. Data is transferred after the 8th SK of 1 cycle.
WADDR
WADDR
RADDR
ADDR
(read)
3
x
2
Figure 14. MICROWIRE/PLUS Interface Block Diagram
1
0
CMD1-0
Table 2. Command/Address Byte Format
Cycle
2-n
1
2
1
1
2
1
DATA_IN
DATA_OUT
Shift in CMD/RADDR; shift out previous read data
Shift in next CMD/ADDR; shift out RADDR data
no action; shift out previous read data (do not clear CoR bits)
Shift in CMD/WADDR; shift out previous read data
Shift in WADDR write data; shift out WADDR read data (do
not clear CoR bits)
Shift in CMD/WADDR; shift out previous read data
Shift in WADDR write data; shift out WADDR read data (do
not clear CoR bits); terminate this mode by pulling CS high
SHIFT
ADDR
19
Sequence Initiated
Description
Data Out
Address
Data In
1
0x00
0x3F
Register File
www.national.com