MAX3421EETJ+T Maxim Integrated Products, MAX3421EETJ+T Datasheet - Page 16
![IC USB PERIPH/HOST CNTRL 32TQFN](/photos/6/50/65019/32-tqfn_21-0140l_sml.jpg)
MAX3421EETJ+T
Manufacturer Part Number
MAX3421EETJ+T
Description
IC USB PERIPH/HOST CNTRL 32TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX3421EETJ.pdf
(32 pages)
Specifications of MAX3421EETJ+T
Controller Type
USB Peripheral Controller
Interface
USB/Serial
Voltage - Supply
3 V ~ 3.6 V
Current - Supply
15mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-TQFN Exposed Pad
For Use With
MAX3421EVKIT-1+ - EVAL KIT FOR MAX3421E
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
USB Peripheral/Host Controller
with SPI Interface
help sustain bandwidth by allowing data to move concur-
rently over USB and the SPI interface.
Power the USB transceiver and digital logic by apply-
ing a positive 3.3V supply to V
with a 1.0µF ceramic capacitor as close to the V
as possible.
V
other digital inputs and outputs. Connect V
tem’s logic-level power supply. Internal level translators
and V
inputs and outputs to operate at a system voltage
between 1.4V and 3.6V.
The MAX3421E features a USB V
VBCOMP. The VBCOMP pin can withstand input volt-
ages up to 6V. Bypass VBCOMP to GND with a 1.0µF
ceramic capacitor. VBCOMP is internally connected to
a voltage comparator to allow the SPI master to detect
(through an interrupt or checking a register bit) the
presence or loss of power on V
power any internal circuitry inside the MAX3421E.
VBCOMP is pulled down to ground with R
Electrical Characteristics).
VBCOMP is internally connected to a voltage compara-
tor so that the SPI master can detect the presence or
absence of V
tion, a self-powered peripheral must disconnect its
1.5kΩ pullup resistor to D+ in the event that the host
turns off bus power. The VBGATE bit in the USBCTL
(R15) register provides the option for the MAX3421E
internal logic to automatically disconnect the 1.5kΩ
resistor on D+. The VBGATE and CONNECT bits of
USBCTL (R15), along with the VBCOMP comparator
output (VBUS_DET), control the pullup resistor between
V
Diagram. Note that if VBGATE = 1 and VBUS_DET = 0,
the pullup resistor is disconnected regardless of the
CONNECT bit setting. If the device using the
MAX3421E is bus powered (through a +3.3V regulator
connected to V
be used as a general-purpose input. See the
Applications Information section for more details about
this connection.
16
L
CC
acts as a reference level for the SPI interface and all
______________________________________________________________________________________
and D+ as shown in Table 3 and the Functional
L
allow the SPI interface and all general-purpose
BUS
CC
. According to the USB 2.0 specifica-
), the MAX3421E VBCOMP input can
VBCOMP in Peripheral Mode
CC
BUS
. Bypass V
BUS
. VBCOMP does not
detector input,
L
VBCOMP
CC
to the sys-
IN
to GND
CC
V
(see
CC
V
pin
L
When using the MAX3421E in host mode, the presence
of V
VBCOMP input can be used as a general-purpose
input.
The internal USB full-/low-speed transceiver is brought
out to the bidirectional data pins D+ and D-. These pins
are ±15kV ESD protected. Connect D+ and D- to a
USB B connector through 33Ω ±1% series resistors.
In peripheral mode, the D+ and D- pins connect to a
USB B connector through series resistors. A switchable
1.5kΩ pullup resistor is internally connected to D+.
In host mode, the D+ and D- pins connect to a USB A
connector through series resistors. Switchable 15kΩ
pulldown resistors are internally connected to D+ and
D-. The DPPULLDN and DMPULLDN bits in the MODE
(R27) register control the connection between D+ and
D- to GND. For host operation, set these bits to 1 to
enable the pulldown resistors. A host interrupt bit called
CONNIRQ alerts the SPI master when a peripheral is
attached or detached.
XI and XO connect an external 12MHz crystal to the
internal oscillator circuit. XI is the crystal oscillator
input, and XO is the crystal oscillator output. Connect
one side of a 12MHz ±0.25% parallel resonant crystal
to XI, and connect XO to the other side. Connect load
capacitors (20pF max) to ground on both XI and XO. XI
can also be driven with an external 12MHz ±0.25%
clock. If driving XI with an external clock, leave XO
unconnected. The external clock must meet the voltage
characteristics depicted in the Electrical Character-
istics table. Internal logic is single-edge triggered. The
external clock should have a nominal 50% duty cycle.
Table 3. Internal Pullup Resistor Control
in Peripheral Mode
CONNECT
BUS
0
1
1
1
does not need to be detected. In this case, the
VBGATE
X
0
1
1
D+ and D- in Peripheral Mode
VBUS_DET
X
X
0
1
D+ and D- in Host Mode
VBCOMP in Host Mode
Not Connected
Not Connected
Connected
Connected
XI and XO
PULLUP
D+ and D-