ISP1161ABM-T ST-Ericsson Inc, ISP1161ABM-T Datasheet - Page 83
ISP1161ABM-T
Manufacturer Part Number
ISP1161ABM-T
Description
IC USB HOST CTRL FULL-SPD 64LQFP
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1161ABD.pdf
(135 pages)
Specifications of ISP1161ABM-T
Controller Type
USB 2.0 Controller
Interface
Parallel
Voltage - Supply
3.3V, 5V
Current - Supply
47mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1161ABM-T
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
- Current page: 83 of 135
- Download datasheet (586Kb)
Philips Semiconductors
9397 750 13962
Product data
11.4.1 Suspend conditions
11.4 Suspend and resume
The ISP1161A DC detects a USB suspend status when a constant idle state is
present on the USB bus for more than 3 ms.
The bus-powered devices that are suspended must not consume more than 500 µA
of current. This is achieved by shutting down power to system components or
supplying them with a reduced voltage.
The steps leading up to suspend status are as follows:
Figure 38
1. On detecting a wakeup-to-suspend transition, the ISP1161A DC sets
2. When the firmware detects a suspend condition, it must prepare all system
3. In the interrupt service routine, the firmware must check the current status of the
4. To meet the suspend current requirements for a bus-powered device, the internal
5. When the firmware has set and cleared bit GOSUSP in the DcMode register, the
bit SUSPND in the DcInterrupt register. This will generate an interrupt if
bit IESUSP in the DcInterruptEnable register is set.
components for the suspend state:
USB bus. When bit BUSTATUS in the DcInterrupt register is logic 0, the USB bus
has left the suspend mode and the process must be aborted. Otherwise, the next
step can be executed.
clocks must be switched off by clearing bit CLKRUN in the
DcHardwareConfiguration register.
ISP1161A enters the suspend state. In powered-off application, the ISP1161A
DC asserts output SUSPEND and switches off the internal clocks after 2 ms.
a. All signals connected to the ISP1161A DC must enter appropriate states to
b. All input pins of the ISP1161A DC must have a CMOS LOW or HIGH level.
meet the power consumption requirements of the suspend state.
shows a typical timing diagram.
Rev. 03 — 23 December 2004
Full-speed USB single-chip host and device controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1161A
82 of 134
Related parts for ISP1161ABM-T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC FILTR/CODEC 14BIT AUD 30TSSOP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC FILTR/CODEC 14BIT AUD 30TSSOP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HUB CONTROLLER HS 80-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HOST CONTROLLER 128-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB OTG CONTROLLER 64-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB PERIPH CONTROLLER 64HVQFN
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HOST CTRL FULL-SPD 48HVQF
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 64HVQFN
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 64TFBGA
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 64HVQFN
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL SNGL CHIP 64TFBGA
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB HOST/DEVICE CTRLR 64-LQFP
Manufacturer:
ST-Ericsson Inc
Datasheet:
Part Number:
Description:
IC USB CTRL HI-SPEED 128TFBGA
Manufacturer:
ST-Ericsson Inc
Datasheet: