MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 30

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

1-20
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
Delay On Break
Q3T Series
FEATURES
●
●
●
●
●
●
●
●
●
●
●
Operating Logic: Input voltage is applied to
the timer at all times. Upon closure of a nor-
mally open isolated start switch, the load is
energized and remains in this state as long
as the switch is kept closed. When the start
switch is opened, timing starts. At the end
of the preset time delay the output de-ener-
gizes and the unit is ready for a new cycle.
(Start switch supplied by customer.)
Note: 1) Do not apply voltage or ground to the start switch;
2) Switch leads should be shielded when running close to other
wires; 3) If the start switch is re-closed during timing the timer will
reset and will not start timing until the start switch is opened.
LOGIC FUNCTION DIAGRAM
Input
Voltage
Start
Switch
Load
100% functionally tested
Solid state digital timing
Time delays to 1 hour standard
20:1 maximum to minimum timing ratio
Cost efficient
Compact size
Superior transient protection
Epoxy encapsulated
Flame-retardant and solvent-resistant
polyester thermoplastic housing
Trimpot on-board with sealed cermet
element
Closed
Open
On
Off
On
Off
Delay On Break Function
TIME DELAY RELAYS
File #E65038
Timing
(Retriggerable)
ORDERING INFORMATION
SPECIFICATIONS
TIME DELAY
Adjustment: On-board Trimpot
Range: 50 ms to 1 hour in 7 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy: Maximum time +10%, -0%;
Minimum time -30%, +0%
Reset Time: .5 seconds max. by removal of the
input voltage
INPUT
Operating Voltage: 120/240 VAC ±10%
Frequency: 50/60 Hz
OUTPUT
Type: Solid state normally open
Rating: 1 A resistive or inductive
Life: 100,000,000 cycles
PROTECTION
Transient Voltage: 30 joule metal oxide varistor
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
Isolation Resistance: 100 megohms min.
between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: Surface mount with one #8 screw
ENVIRONMENTAL
Storage Temperature: -40°C to 85°C
Operating Temperature: -40°C to 65°C
Humidity: 95% relative
Trigger time (start switch closure)
Reset time
Min. load
Max. leakage current
Voltage drop at 1 A
Power consumption
Peak 1 cycle surge
Protection
180 to 3600 sec.
15 to 300 sec.
30 to 600 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
3 to 60 sec.
120 VAC +10%
Q3T-00001-321
Q3T-00005-321
Q3T-00010-321
Q3T-00060-321
Q3T-00300-321
Q3T-00600-321
Q3T-03600-321
4.3 VA max.
3.3 V max.
30j. MOV
500 ms
200 uA
20 ms
2 mA
20 A
START
SWITCH
TIME DELAY
ADJUSTMENT ACCESS
Consult factory for any special
requirements not listed in catalog
(minimum order requirement may
apply).
(3667-4)
LOAD
1
.25 X .032 MALE FAST-ON
2.00 SQ.
240 VAC +10%
Q3T-00300-325
TERMINALS (5 PL.)
Polarity Shown is
for D.C. Models
C L
2
VOLTAGE
—
—
—
—
—
—
1.25
INPUT
.88
3
L C
DIA.
.170