DS90LT012AHMF/NOPB National Semiconductor, DS90LT012AHMF/NOPB Datasheet - Page 3

• Manufacturer Part Number: DS90LT012AHMF/NOPB
• Description: IC RCVR LVDS DIFF RTERM SOT23-5
• Manufacturer: National Semiconductor
• Type: Line Receiverr

Specifications of DS90LT012AHMF/NOPB

• Number Of Drivers/receivers: 0/1
• Protocol: LVDS
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Number Of Elements: 1
• Number Of Receivers: 1
• Number Of Drivers: 1
• Input Type: CMOS/TTL
• Operating Supply Voltage (typ): 3.3V
• Diff. Input Low Threshold Volt: -100mV
• Propagation Delay Time: 3.5ns
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 5
• Package Type: SOT-23
• Supply Current: 10µA
• Supply Voltage Range: 2.7V To 3.6V
• Driver Case Style: SOT-23
• No. Of Pins: 5
• Operating Temperature Range: -40°C To +85°C
• Device Type: Differential Line Receiver
• Rohs Compliant: Yes
• Data Rate Max: 400Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DS90LT012AHMF/NOPBTR

t
t
t
t
t
t
t
f
Symbol
PHLD
PLHD
SKD1
SKD3
SKD4
TLH
THL
MAX
Switching Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. (Notes 6, 7)
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise
specified (such as V
Note 3: All typicals are given for: V
Note 4: ESD Ratings:
DS90LT012AH:
Note 5: Output short circuit current (I
exceed maximum junction temperature specification.
Note 6: C
Note 7: Generator waveform for all tests unless otherwise specified: f = 1 MHz, Z
Note 8: t
Note 9: t
and within 5˚C of each other within the operating temperature range.
Note 10: t
recommended operating temperature and voltage ranges, and across process distribution. t
Note 11: V
V
V
Note 12: f
V
over the PVT range by the transition times (t
Parameter Measurement Information
DD
DD
OL
(max 0.4V), V
− 0.3V when V
− 0.3V when V
HBM (1.5 kΩ, 100 pF) ≥ 2kV
EIAJ (0Ω, 200 pF) ≥ 700V
CDM ≥ 2000V
IEC direct (330Ω, 150 pF) ≥ 7kV
SKD1
SKD3
Differential Propagation Delay High to Low
Differential Propagation Delay Low to High
Differential Pulse Skew |t
Differential Part to Part Skew (Note 9)
Differential Part to Part Skew (Note 10)
Rise Time
Fall Time
Maximum Operating Frequency (Note 12)
L
MAX
SKD4
includes probe and jig capacitance.
DD
, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices at the same V
is the magnitude difference in differential propagation delay time between the positive-going-edge and the negative-going-edge of the same channel.
is always higher than IN+ and IN− voltage. IN+ and IN− are allowed to have voltage range −0.05V to +2.35V when V
generator input conditions: t
, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices over the
OH
DD
DD
ID
(min 2.4V), load = 15 pF (stray plus probes). The parameter is guaranteed by design. The limit is based on the statistical analysis of the device
).
= 3.0V to 3.6V.
= 3.0V to 3.6V. V
FIGURE 1. Receiver Propagation Delay and Transition Time Test Circuit
DD
OS
= +3.3V and T
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not
Parameter
ID
PHLD
r
is not allowed to be greater than 100 mV when V
= t
TLH
f
<
− t
and t
1 ns (0% to 100%), 50% duty cycle, differential (1.05V to 1.35 peak to peak). Output criteria: 60%/40% duty cycle,
PLHD
A
THL
= +25˚C.
).
| (Note 8)
3
O
= 50Ω, t
C
V
(Figure 1 and Figure 2)
L
ID
SKD4
= 15 pF
r
= 200 mV
CM
and t
Conditions
is defined as |Max − Min| differential propagation delay.
= 0.05V to 2.35V when V
f
(0% to 100%) ≤ 3 ns for IN
20161603
DD
Min
200
1.0
1.0
0
0
0
= 2.7V or when V
±
.
DD
Typ
100
350
175
250
1.8
1.7
0.3
0.4
= 2.7V and |V
CM
Max
400
800
800
3.5
3.5
1.0
1.5
www.national.com
= |V
ID
ID
| / 2 to
| / 2 to
Units
MHz
ns
ns
ps
ns
ns
ps
ps
DD