LAN8720AI-CP SMSC, LAN8720AI-CP Datasheet - Page 20
![TXRX ETHERNET 10/100 RMII 24QFN](/photos/6/86/68648/24-qfn_sml.jpg)
LAN8720AI-CP
Manufacturer Part Number
LAN8720AI-CP
Description
TXRX ETHERNET 10/100 RMII 24QFN
Manufacturer
SMSC
Type
Transceiverr
Specifications of LAN8720AI-CP
Number Of Drivers/receivers
4/4
Protocol
RMII
Voltage - Supply
1.6 V ~ 3.6 V
Mounting Type
Surface Mount
Package / Case
24-QFN
Product
Ethernet Transceivers
Standard Supported
802.3, 802.3u
Supply Voltage (max)
3.6 V
Supply Voltage (min)
1.6 V
Maximum Operating Temperature
+ 85 C
Ethernet Connection Type
10/100 Base-T
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
638-1084
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN8720AI-CP
Manufacturer:
Standard
Quantity:
5 016
Company:
Part Number:
LAN8720AI-CP
Manufacturer:
VISHAY
Quantity:
14 585
Part Number:
LAN8720AI-CP
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
LAN8720AI-CP-TR
Manufacturer:
CHIPLUS
Quantity:
3 100
Revision 1.2 (11-10-10)
3.1.2
3.1.2.1
3.1.2.2
3.1.2.3
MAC
Converter
Converter
NRZI
100BASE-TX Receive
The 100BASE-TX receive data path is shown in
following subsections.
100M Receive Input
The MLT-3 from the cable is fed into the transceiver (on inputs RXP and RXN) via a 1:1 ratio
transformer. The ADC samples the incoming differential signal at a rate of 125M samples per second.
Using a 64-level quanitizer, it generates 6 digital bits to represent each sample. The DSP adjusts the
gain of the ADC according to the observed signal levels such that the full dynamic range of the ADC
can be used.
Equalizer, Baseline Wander Correction and Clock and Data Recovery
The 6 bits from the ADC are fed into the DSP block. The equalizer in the DSP section compensates
for phase and amplitude distortion caused by the physical channel consisting of magnetics, connectors,
and CAT- 5 cable. The equalizer can restore the signal for any good-quality CAT-5 cable between 1m
and 150m.
If the DC content of the signal is such that the low-frequency components fall below the low frequency
pole of the isolation transformer, then the droop characteristics of the transformer will become
significant and Baseline Wander (BLW) on the received signal will result. To prevent corruption of the
received data, the transceiver corrects for BLW and can receive the ANSI X3.263-1995 FDDI TP-PMD
defined “killer packet” with no bit errors.
The 100M PLL generates multiple phases of the 125MHz clock. A multiplexer, controlled by the timing
unit of the DSP, selects the optimum phase for sampling the data. This is used as the received
recovered clock. This clock is used to extract the serial data from the received signal.
NRZI and MLT-3 Decoding
The DSP generates the MLT-3 recovered levels that are fed to the MLT-3 converter. The MLT-3 is then
converted to an NRZI data stream.
A/D
RMII 50Mhz by 2 bits
Ext Ref_CLK
NRZI
MLT-3
Converter
MLT-3
Magnetics
Figure 3.2 100BASE-TX Receive Data Path
PLL
RMII
MLT-3
DATASHEET
by 4 bits
125 Mbps Serial
25MHz
MLT-3
6 bit Data
20
RJ45
Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support
Figure
Decoder
4B/5B
and BLW Correction
recovery, Equalizer
MLT-3
3.2. Each major block is explained in the
DSP: Timing
CAT-5
25MHz by
5 bits
SMSC LAN8720A/LAN8720Ai
Descrambler
and SIPO
Datasheet