DSPIC30F6010A-30I/PT Microchip Technology Inc., DSPIC30F6010A-30I/PT Datasheet - Page 163
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
DSPIC30F6010A-30I/PT
Manufacturer Part Number
DSPIC30F6010A-30I/PT
Description
16 BIT MCU/DSP 80LD 30MIPS 144 KB FLASH
Manufacturer
Microchip Technology Inc.
Type
DSPr
Datasheet
1.DSPIC30F6010A-30IPT.pdf
(244 pages)
Specifications of DSPIC30F6010A-30I/PT
A/d Inputs
16-Channels, 10-Bit
Cpu Speed
30 MIPS
Eeprom Memory
4K Bytes
Input Output
68
Interface
CAN, I2C, SPI, UART/USART
Ios
68
Memory Type
Flash
Number Of Bits
16
Package Type
80-pin TQFP
Programmable Memory
144K Bytes
Ram Size
8K Bytes
Timers
5-16-bit, 2-32-bit
Voltage, Range
2.5-5.5
Lead Free Status / Rohs Status
RoHS Compliant part
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F6010A-30I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F6010A-30I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
21.4
21.4.1
The primary function of the Watchdog Timer (WDT) is
to reset the processor in the event of a software mal-
function. The WDT is a free running timer, which runs
off an on-chip RC oscillator, requiring no external com-
ponent. Therefore, the WDT timer will continue to oper-
ate even if the main processor clock (e.g., the crystal
oscillator) fails.
21.4.2
The Watchdog Timer can be “Enabled” or “Disabled”
only through a configuration bit (FWDTEN) in the
configuration register FWDT.
Setting FWDTEN = 1 enables the Watchdog Timer.
The enabling is done when programming the device.
By default, after chip-erase, FWDTEN bit = 1. Any
device
dsPIC30F devices allows programming of this and
other configuration bits.
If enabled, the WDT will increment until it overflows or
“times out”. A WDT time-out will force a device Reset
(except during Sleep). To prevent a WDT time-out, the
user must clear the Watchdog Timer using a CLRWDT
instruction.
If a WDT times out during Sleep, the device will wake-
up. The WDTO bit in the RCON register will be cleared
to indicate a wake-up resulting from a WDT time-out.
Setting FWDTEN = 0 allows user software to enable/
disable the Watchdog Timer via the SWDTEN
(RCON<5>) control bit.
21.5
The Low Voltage Detect (LVD) module is used to detect
when the V
value V
(RCON<11:8>) and is thus user-programmable. The
internal voltage reference circuitry requires a nominal
amount of time to stabilize, and the BGST bit
(RCON<13>) indicates when the voltage reference has
stabilized.
In some devices, the LVD threshold voltage may be
applied externally on the LVDIN pin.
The LVD module is enabled by setting the LVDEN bit
(RCON<12>).
2004 Microchip Technology Inc.
LVD
Low Voltage Detect
programmer
Watchdog Timer (WDT)
, which is determined by the LVDL<3:0> bits
WATCHDOG TIMER OPERATION
ENABLING AND DISABLING THE
WDT
DD
of the device drops below a threshold
capable
of
programming
Preliminary
21.6
There are two power saving states that can be entered
through the execution of a special instruction, PWRSAV.
These are: Sleep and Idle.
The format of the PWRSAV instruction is as follows:
PWRSAV <parameter>, where ‘parameter’ defines
Idle or Sleep mode.
21.6.1
In Sleep mode, the clock to the CPU and peripherals is
shutdown. If an on-chip oscillator is being used, it is
shutdown.
The fail-safe clock monitor is not functional during
Sleep, since there is no clock to monitor. However,
LPRC clock remains active if WDT is operational during
Sleep.
The Brown-out protection circuit and the Low Voltage
Detect circuit, if enabled, will remain functional during
Sleep.
The processor wakes up from Sleep if at least one of
the following conditions has occurred:
• any interrupt that is individually enabled and
• any Reset (POR, BOR and MCLR)
• WDT time-out
On waking up from Sleep mode, the processor will
restart the same clock that was active prior to entry
into Sleep mode. When clock switching is enabled,
bits COSC<1:0> will determine the oscillator source
that will be used on wake-up. If clock switch is
disabled, then there is only one system clock.
If the clock source is an oscillator, the clock to the
device will be held off until OST times out (indicating a
stable oscillator). If PLL is used, the system clock is
held off until LOCK = 1 (indicating that the PLL is sta-
ble). In either case, T
applied.
If EC, FRC, LPRC or EXTRC oscillators are used, then
a delay of T
delay possible on wake-up from Sleep.
Moreover, if LP oscillator was active during Sleep, and
LP is the oscillator used on wake-up, then the start-up
delay will be equal to T
timer delay are not applied. In order to have the small-
est possible start-up delay when waking up from Sleep,
one of these faster wake-up options should be selected
before entering Sleep.
meets the required priority level
Note:
Power Saving Modes
POR
SLEEP MODE
If a POR or BOR occurred, the selection of
the oscillator is based on the FOS<1:0>
and FPR<3:0> configuration bits.
(~ 10 µs) is applied. This is the smallest
POR
, T
POR
LOCK
dsPIC30F
. PWRT delay and OST
and T
DS70082G-page 161
PWRT
delays are