HEDS-5645-I13 Avago Technologies US Inc., HEDS-5645-I13 Datasheet
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HEDS-5645-I13
Specifications of HEDS-5645-I13
Related parts for HEDS-5645-I13
HEDS-5645-I13 Summary of contents
Page 1
... This index output electrical degree, high true index pulse which is generated once for each full rotation of the codewheel. The HEDS series utilizes metal codewheels, while the HEDM series utilizes a film codewheel allowing for resolutions to 1024 CPR. The HEDM series is nont available with a third channel index ...
Page 2
... Package Dimensions HEDS-5500/5540, HEDM-5500 *Note: For the HEDS-5500 and HEDM-5500, Pin # Connect. For the HEDS-5540, Pin #2 is CH. I, the index output. HEDS-5600/5640, HEDM-5600 *Note: For the HEDS-5600 and HEDM-5600, Pin # Connect. For the HEDS-5640, Pin #2 is CH. I, the index output. 2 ...
Page 3
... The photodiode outputs are then fed through the signal processing circuitry resulting and B (also I and I in the HEDS-5540 and 5640). Comparators receive these signals and produce the final outputs for channels A and B. Due to this integrated phasing ...
Page 4
... B. If the codewheel rotates in the clockwise direction, channel B will lead channel A. ): The Index Pulse Width (P O number of electrical degrees that an index output is high during one full shaft rotation. This value is nominally 1/4 cycle. HEDS-55XX/56XX - 100 C - 100 OUT 1000 Hz 0. 0.010 in.) ...
Page 5
... Parameter Temperature HEDS Series Temperature HEDM Series Supply Voltage Load Capacitance Count Frequency Shaft Perpendicularity Plus Axial Play (HEDS Series) Shaft Eccentricity Plus Radial Play (HEDS Series) Shaft Perpendicularity Plus Axial Play (HEDM Series) Shaft Eccentricity Plus Radial Play(HEDM Series) Note: The module performance is guaranteed to 100 kHz but can operate at higher frequencies. 2.7 k required for HEDS-5540 and 5640 ...
Page 6
... Parameter HEDS-5500 Supply Current HEDS-5600 High Level Output Voltage Low Level Output Voltage Rise Time Fall Time HEDS-5540 Supply Current HEDS-5640 High Level Output Voltage HEDM-5500 Low Level Output Voltage HEDM-5600 Rise Time Fall Time HEDM-5500 Supply Current HEDM-5600 High Level Output Voltage ...
Page 7
... The HEDS-55X5 and 56X5, HEDM-5505, 5605 provide an 8.9 mm (0.35 inch) diameter hole through the housing for longer motor shafts. See Ordering Information. 3. The HEDS-5540 and 5640 must be aligned using the aligning pins as specified in Figure 3, or using the alignment tool as shown in “Encoder Mounting and Assembly”. See also “Mounting Considerations.” ...
Page 8
... Figure 1. Pull-up Resistors on HEDS-5X40 Encoder Outputs. Mounting Considerations The HEDS-5540 and 5640 three channel encoders and the HEDM Series high resolution encoders must be aligned using the aligning pins as specified in Figure 3, or using the HEDS-8910 Alignment Tool as shown in Encoder Mounting and Assembly. ...
Page 9
Figure 4. Mounting with External Ears. 9 2.39 / 2.34 (0.096 / 0.092) 0.25 (0.010) X 45° CHAMFER 2 PLACES A Ø 0.15 (0.006) 0.8 (0.03) X 45° CHAMFER O A 0.05 (0.002) 11.10 / 10.94 (0.438 / 0.431) ...
Page 10
... Encoder Mounting and Assembly 1. For HEDS-5500 and 5600: Mount encoder base plate onto motor. Tighten screws step 2. 1a. For HEDS-5540, 5640 and HEDM-5500, 5600: Slip alignment tool onto motor shaft. With alignment tool in place, mount encoder baseplate onto motor as shown above. ...
Page 11
... DECODER/ HEDM-5X0X COUNTER HEDS–55XX CH HCTL-1100 HEDS-56XX CH. B MOTION OR CONTROL IC HEDM-5X0X Part Number 103686-4 640442-5 65039-032 with 4825X-000 term. HEDS-8902 (2 ch.) with 4-wire leads HEDS-8903 (3 ch.) with 5-wire leads 2695 series with 2759 series term. * HOST 2020 PROCESSOR HOST PROCESSOR 11 * N/A * ...
Page 12
... HEDM-550X/560X two channel encoders) Encoders with Metal Codewheels Mounting Type Outputs 5 - Standard Channel 6 - External Channel Mounting Ears (Included with each order of HEDS-554X/564X three channel encoders) HEDM-5 0 Option Through Hole Resolution (Cycles/Rev None B - 1000 CPR 5 - 8.9 mm (0.35 in.) ...
Page 13
... HEDM-5500 HEDM-5505 HEDM-5600 B J HEDM-5605 B J HEDS-5500 HEDS-5505 HEDS-5540 HEDS-5545 HEDS-5600 ...
Page 14
... HEDS-5605 HEDS-5640 HEDS-5645 ...
Page 15
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 271 ...