DS90LT012AQMF/NOPB National Semiconductor, DS90LT012AQMF/NOPB Datasheet - Page 3

• Manufacturer Part Number: DS90LT012AQMF/NOPB
• Description: IC LINE RCVR LVDS DIFF SOT23-5
• Manufacturer: National Semiconductor
• Type: Line Receiverr

Specifications of DS90LT012AQMF/NOPB

• Number Of Drivers/receivers: 0/1
• Protocol: LVDS
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Number Of Elements: 1
• Number Of Receivers: 1
• Number Of Drivers: 1
• Input Type: CMOS
• Operating Supply Voltage (typ): 3.3V
• Diff. Input Low Threshold Volt: -100mV
• Transmission Data Rate: 400Mbps
• Propagation Delay Time: 3.5ns
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 5
• Package Type: SOT-23
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DS90LT012AQMF

t
t
t
t
t
t
t
f
Symbol
PHLD
PLHD
SKD1
SKD3
SKD4
TLH
THL
MAX
Switching Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified.
Note 4: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 5: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise
specified (such as V
Note 6: All typicals are given for: V
Note 7: Output short circuit current (I
exceed maximum junction temperature specification.
Note 8: These parameters are guaranteed by design. The limits are based on statistical analysis of the device performance over PVT (process, voltage,
temperature) ranges.
Note 9: C
Note 10: Generator waveform for all tests unless otherwise specified: f = 1 MHz, Z
Note 11: t
channel.
Note 12: t
V
Note 13: t
recommended operating temperature and voltage ranges, and across process distribution. t
Note 14: f
cycle, V
Parameter Measurement Information
DD
and within 5°C of each other within the operating temperature range.
OL
Differential Propagation Delay High to Low
Differential Propagation Delay Low to High
Differential Pulse Skew |t
Differential Part to Part Skew
Differential Part to Part Skew
Rise Time
Fall Time
Maximum Operating Frequency
L
SKD1
SKD3
(max 0.4V), V
SKD4
MAX
includes probe and jig capacitance.
, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices at the same
generator input conditions: t
is the magnitude difference in differential propagation delay time between the positive-going-edge and the negative-going-edge of the same
, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices over the
ID
).
OH
(min 2.4V), load = 15 pF (stray plus probes).
FIGURE 1. Receiver Propagation Delay and Transition Time Test Circuit
FIGURE 2. Receiver Propagation Delay and Transition Time Waveforms
DD
OS
= +3.3V and T
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not
PHLD
Parameter
r
= t
(Note
(Note
− t
f
< 1 ns (0% to 100%), 50% duty cycle, differential (1.05V to 1.35 peak to peak). Output criteria: 60%/40% duty
(Note
PLHD
A
12)
13)
= +25°C.
|
(Note
14)
11)
3
O
= 50Ω, t
C
V
(Figure 1
ID
L
= 15 pF
SKD4
= 200 mV
r
and t
Conditions
is defined as |Max − Min| differential propagation delay.
f
and
(0% to 100%)
Figure
(Note
30063903
2)
6,
≤
3 ns for IN±.
Note
Min
8,
1.0
1.0
0
0
0
30063904
Note
9,
Typ
100
350
175
250
1.8
1.7
0.3
0.4
Note
10)
Max
www.national.com
400
800
800
3.5
3.5
1.0
2.5
Units
MHz
ns
ns
ps
ns
ns
ps
ps