ISL8485EIB-T Intersil, ISL8485EIB-T Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL8485EIB-T
Manufacturer Part Number
ISL8485EIB-T
Description
IC TXRX RS485/422 5V ESD 8-SOIC
Manufacturer
Intersil
Type
Transceiverr
Datasheet
1.ISL8485ECBZ.pdf
(14 pages)
Specifications of ISL8485EIB-T
Number Of Drivers/receivers
1/1
Protocol
RS422, RS485
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL8485EIB-T
Manufacturer:
INTERSIL
Quantity:
20 000
Test Circuits and Waveforms
Electrical Specifications
NOTES:
10. Devices meeting these limits are denoted as “single unit load (1 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus.
12. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
11. Limits established by characterization and are not production tested
Driver Enable from Shutdown to
Output Low
Receiver Enable from Shutdown to
Output High
Receiver Enable from Shutdown to
Output Low
ESD PERFORMANCE
RS-485 Pins (A/Y, B/Z)
All Other Pins
2. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
3. Supply current specification is valid for loaded drivers when DE = 0V.
4. Applies to peak current. See “Typical Performance Curves” on page 10 for more information.
5. When testing the ISL8483E, keep RE = 0 to prevent the device from entering SHDN.
6. When testing the ISL8483E, the RE signal high time must be short enough (typically <200ns) to prevent the device from entering SHDN.
7. The ISL8483E is put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts are guaranteed
8. Keep RE = V
9. Set the RE signal high time >600ns to ensure that the device enters SHDN.
otherwise specified.
not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low Power
Shutdown Mode (ISL8483E Only)” on page 9.
characterization and are not production tested.
PARAMETER
CC
, and set the DE signal low time >600ns to ensure that the device enters SHDN.
6
Test Conditions: V
Typicals are at V
t
t
t
SYMBOL
ZH(SHDN)
ZL(SHDN)
ZL(SHDN)
V
CC
C
C
C
Human Body Model
DE
DI
L
L
L
CC
= 100pF, SW = V
= 15pF, SW = GND, (Figure 5), (Notes 7, 9)
= 15pF, SW = V
CC
FIGURE 1. DRIVER V
= 5V, T
ISL8483E, ISL8485E
D
= 4.5V to 5.5V; Unless Otherwise Specified.
Z
Y
TEST CONDITIONS
A
= +25°C, (Note 2) (Continued)
CC
CC
V
, (Figure 5), (Notes 7, 9)
.
, (Figure 5), (Notes 7, 8)
OD
OD
AND V
R
R
OC
V
OC
TEMP
(°C)
Full
Full
Full
25
25
(Note 12)
MIN
-
-
-
-
-
TYP
>±7
±15
-
-
-
(Note 12) UNITS
MAX
2000
2500
2500
September 9, 2008
-
-
FN6048.9
ns
ns
ns
kV
kV