PCA9673PW,118 NXP Semiconductors, PCA9673PW,118 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
PCA9673PW,118
Manufacturer Part Number
PCA9673PW,118
Description
IC I/O EXPANDER I2C 16B 24TSSOP
Manufacturer
NXP Semiconductors
Datasheet
1.PCA9673PW112.pdf
(33 pages)
Specifications of PCA9673PW,118
Package / Case
24-TSSOP
Interface
I²C
Number Of I /o
16
Interrupt Output
Yes
Frequency - Clock
1MHz
Voltage - Supply
2.3 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Includes
POR
Logic Family
PCA
Operating Supply Voltage
2.3 V to 5.5 V
Power Dissipation
600 mW
Operating Temperature Range
- 40 C to + 85 C
Mounting Style
SMD/SMT
Output Current
50 mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
935283558118
PCA9673PW-T
PCA9673PW-T
PCA9673PW-T
PCA9673PW-T
NXP Semiconductors
PCA9673_1
Product data sheet
The Device ID is read-only, hardwired in the device and can be accessed as follows:
1. START command
2. The master sends the Reserved Device ID I
3. The master sends the I
4. The master sends a Re-START command.
5. The master sends the Reserved Device ID I
6. The device ID read can be done, starting with the 8 manufacturer bits (first byte +
7. The master ends the reading sequence by NACKing the last byte, thus resetting the
Fig 13. PCA9673 ID
•
3 bits with the die revision, assigned by manufacturer (for example, Rev X).
bit set to 0 (write).
The LSB is a ‘Don’t care’ value. Only one device must acknowledge this byte (the one
that has the I
Remark: A STOP command followed by a START command will reset the slave state
machine and the Device ID read cannot be performed.
Remark: A STOP command or a Re-START command followed by an access to
another slave device will reset the slave state machine and the Device ID read cannot
be performed.
bit set to 1 (read).
4 MSB of the second byte), followed by the 13 part identification bits and then the
3 die revision bits (3 LSB of the third byte).
slave device state machine and allowing the master to send the STOP command.
Remark: The reading of the Device ID can be stopped anytime by sending a NACK
command.
Remark: If the master continues to ACK the bytes after the third byte, the PCA9673
rolls back to the first byte and keeps sending the Device ID sequence until a NACK
has been detected.
For the PCA9673, the Device ID is as shown in
part identification
Remote 16-bit I/O expander for Fm+ I
2
C-bus slave address).
Rev. 01 — 1 February 2007
2
0
C-bus slave address of the slave device it needs to identify.
0
category identification
manufacturer
0
0
0
0
0
2
2
C-bus address ‘1111 100’ with the R/W
C-bus address ‘1111 100’ with the R/W
0
1
Figure
0
0
2
C-bus with interrupt and reset
feature identification
0
0
revision
13.
0
0
0
1
0
002aac333
0
0
0
PCA9673
© NXP B.V. 2007. All rights reserved.
0
0
0
9 of 33