MC33793DR2 Freescale Semiconductor, MC33793DR2 Datasheet - Page 11

• Manufacturer Part Number: MC33793DR2
• Description: IC DSI SLAVE FOR R-SENSE 16-SOIC
• Manufacturer: Freescale Semiconductor
• Type: Distributed Systems Interfacer

Specifications of MC33793DR2

• Input Type: Logic
• Output Type: Logic
• Interface: 2 Line, I²C (CLK, Address/Data)
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: MC33793DR2TR

part is reset. The purpose of this is to allow the part to reset
itself if the connection to the master is lost or if power is
removed from the system.
5.0 V REGULATOR
and also provides approximately 6.0 mA through the
REGOUT pin to power an external sensor.
UNDERVOLTAGE DETECTOR
the 5.0 V regulator. If the REGOUT voltage drops too low for
accurate A/D operation, a signal is sent to the control logic.
The control logic will interpret this signal and, in response to
a command, report a status indicating an undervoltage
condition to have existed. When received, the command will
clear the signal after having read the status. If the voltage is
too low when the A/D conversion was completed, the
returned value will be zero (binary 00000000).
IO PINS 0 TO 3
analog inputs. At power-up or after a clear, the pins are all
logic inputs and can be used to measure an analog level
value for an analog value request command. The pins can be
individually configured as logic inputs or outputs by the IO
Control command. If the pin is configured as a logic output,
reading the analog value will return the analog level the
output is being driven to.
ANALOG-TO-DIGITAL CONVERTER
on-board capacitive division. It uses the Clk signal from the
on-board oscillator for sequencing.
and ground AGND for a zero-level reference.
asserting a signal to the controller. If this signal is not
asserted when a value is being captured by the controller, the
controller will signal that an invalid A/D value was obtained.
control logic to signal an error. A value of “0” from the ADC
will be reported as “1” (binary 00000001) by the control logic.
SERIAL ENCODER
ADC and formatting/data from the Control Logic. A logic
transition from Idle to Signal High and then to Signal Low at
BUSIN will cause the first bit to be presented to the current
switch (Response Loading). A transition to Signal High and
back to Signal Low will cause the next bit to be presented to
the current switch. This will continue until a transition back to
Idle turns off the current switch.
SLEW
of switching the bus loading current sink element. The slew
Analog Integrated Circuit Device Data
Freescale Semiconductor
The 5.0 V regulator supplies internal power for the device
The undervoltage detector monitors the output voltage of
The IO pins can serve as logic inputs, logic outputs, or
The ADC is an 8-bit successive approximation type using
The ADC uses REGOUT as a full-scale reference voltage
The ADC signals when it has made a valid conversion by
The value of “0" (binary 00000000) is reserved by the
The Serial Encoder accepts the digitized value from the
The slew circuit serves to reduce EMI produced as a result
circuit limits the rise and fall time of current loading the bus by
controlling the current sinking element.
SWITCHED CURRENT SOURCE
current source. During signaling time, the 33793 will be using
power from H_CAP and not loading the bus for power. The
current will be drawn from either BUSIN or BUSOUT or split
between them. The split can be in any proportion as long as
the total is correct.
level.
LEVEL DETECTOR
the BUSIN or BUSOUT is at idle, logic high, or logic low. The
inputs from BUSIN and BUSOUT are sensed by the device
so that if either side is driven by the signaling waveform while
the other is not, the signaling will be detected. This circuit also
provides a signal to indicate if the signal is being received on
the BUSOUT pin. If a "reverse initialization" command is
received, it can only be acted upon if the device is not already
initialized and if the signal is present on BUSOUT.
SERIAL DECODER
BUSOUT. When the 33793 is Idle and supplying power to
itself and the external device(s) (via REGOUT), the input to
BUSIN will be in the Idle state. A transition from this level to
Signal Low (through Signal High) will start the process of
decoding a word of data. BUSIN is driven from Signal Low to
Signal High for each bit and back to Signal Low to start the
next bit. The determination of whether the bit was a one or a
zero is made by determining whether it spent more time low
(a zero) or high (a one). The end of the word is signaled by a
transition at the end of the last bit from Signal High to Idle.
The advantage of this method is that it will accept data over
a wide range of rates and is not dependent on an accurate
clock.
spending 2/3 of the bit period at Signal Low and 1/3 at Signal
High. A logic one would be 1/3 of the bit period at Signal Low
and 2/3 at Signal High.
CONTROL LOGIC
out by this device. Its principle functions include:
A "1" data return bit will be signaled by turning on a fixed
The current source is turned off whenever the bus is at Idle
The level detector contains comparators to determine if
The Serial Decoder monitors transitions on the BUSIN or
The controller will typically indicate a logic zero by
The control logic performs the digital operations carried
• Decoding input instructions.
• Control the general purpose I/O and LOGICOUT in
• Control A/D conversions.
• Form response word.
• Capture and store address.
• Control BUSSW.
• Reset device on power-up.
• Control the general purpose I/O logic configuration.
response to BUSIN or BUSOUT commands.
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
FUNCTIONAL DESCRIPTION
33793
11