MC14467P1 Freescale Semiconductor, MC14467P1 Datasheet - Page 5

• Manufacturer Part Number: MC14467P1
• Description: IC SMOKE DETECTOR 16-DIP
• Manufacturer: Freescale Semiconductor
• Type: Smoke Detectorr

Specifications of MC14467P1

• Input Type: Voltage
• Output Type: Voltage
• Current - Supply: 12µA
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Interface: -
• Other names: MC14467-1

TIMING
period of 1.67 seconds during no–smoke conditions. Each
1.67 seconds, internal power is applied to the entire IC and a
check is made for smoke, except during LED pulse, Low Bat-
tery Alarm Chirp, or Horn Modulation (in smoke). Every 24
clock cycles a check is made for low battery by comparing
V
are used in the oscillator, the oscillator capacitor should be of
a low leakage type.
DETECT CIRCUITRY
and the piezoelectric horn oscillator circuit is enabled. The
horn output is modulated 160 ms on, 80 ms off. During the off
time, smoke is again checked and will inhibit further horn out-
put if no smoke is sensed. During smoke conditions the low
battery alarm is inhibited, but the LED pulses at a 1.0 Hz rate.
detect input. The voltage at these pins will be within 100 mV
of the input signal. This will keep surface leakage currents to
a minimum and provide a method of measuring the input volt-
age without loading the ionization chamber. The active guard
op amp is not power strobed and thus gives constant protec-
tion from surface leakage currents. Pin 15 (the Detect input)
has internal diode protection against static damage.
SENSITIVITY/LOW BATTERY THRESHOLDS
levels are set internally by a common voltage divider (please
DD
Motorola Sensor Device Data
The internal oscillator of the MC14467–1 operates with a
If smoke is detected, the oscillator period becomes 40 ms
An active guard is provided on both pins adjacent to the
Both the sensitivity threshold and the low battery voltage
to an internal zener voltage. Since very small currents
0.1 F
+
9 V
*NOTE: Component values may change depending on type of piezoelectric horn used.
8.2 M
330
Figure 5. Typical Application as Ionization Smoke Detector
1
2
3
4
5
6
7
8
MC14467–1
16
DEVICE OPERATION
15
14
13
12
11
10
9
1.5 M *
0.001* F
see Figure 1) connected between V
ages can be altered by external resistors connected from
pins 3 or 13 to either V
action here due to the common voltage divider network. The
sensitivity threshold can also be set by adjusting the smoke
chamber ionization source.
TEST MODE
strobed, adjustments for sensitivity or low battery level could
be difficult and/or time–consuming. By forcing Pin 12 to V
the power strobing is bypassed and the outputs, Pins 1 and
4, constantly show smoke/no smoke and good battery/low
battery, respectively. Pin 1 = V
for low battery. In this mode and during the 10 ms power
strobe, chip current rises to approximately 50 A.
LED PULSE
ing the LED pulse. The battery is loaded via a 10 mA pulse
for 10 ms. If the LED is not used, it should be replaced with
an equivalent resistor such that the battery loading remains
at 10 mA.
HYSTERESIS
sets sensitivity is altered to increase sensitivity. This yields
approximately 100 mV of hysteresis and reduces false
triggering.
Since the internal op amps and comparators are power
The 9–volt battery level is checked every 40 seconds dur-
When smoke is detected, the resistor/divider network that
220 k *
0.1 F
DD
or V
1 M
SS
DD
. There will be a slight inter-
for smoke and Pin 4 = V
DD
and V
1 M
MC14467-1
SS
. These volt-
TEST
5
SS
DD
,