DS92LV1224TMSA/NOPB National Semiconductor, DS92LV1224TMSA/NOPB Datasheet - Page 2
![IC DESERIALIZER 10-BIT 28-SSOP](/photos/6/64/66427/pkg_msa28_sml.jpg)
DS92LV1224TMSA/NOPB
Manufacturer Part Number
DS92LV1224TMSA/NOPB
Description
IC DESERIALIZER 10-BIT 28-SSOP
Manufacturer
National Semiconductor
Datasheet
1.DS92LV1224TMSANOPB.pdf
(13 pages)
Specifications of DS92LV1224TMSA/NOPB
Function
Deserializer
Data Rate
660Mbps
Input Type
LVDS
Output Type
LVTTL
Number Of Inputs
1
Number Of Outputs
10
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*DS92LV1224TMSA
*DS92LV1224TMSA/NOPB
DS92LV1224TMSA
*DS92LV1224TMSA/NOPB
DS92LV1224TMSA
www.national.com
Block Diagrams
Functional Description
The DS92LV1023 is a 10-bit Serializer device which together
with a compatible deserializer (i.e. DS92LV1224) forms a
chipset designed to transmit data over FR-4 printed circuit
board backplanes and balanced copper cables at clock
speeds from 40 to 66 MHz.
The chipset has three active states of operation: Initializa-
tion, Data Transfer, and Resynchronization; and two passive
states: Powerdown and TRI-STATE
The following sections describe each operation and passive
state.
Initialization
Initialization of both devices must occur before data trans-
mission begins. Initialization refers to synchronization of the
Serializer and Deserializer PLL’s to local clocks, which may
be the same or separate. Afterwards, synchronization of the
Deserializer to Serializer occurs.
Step 1: When you apply V
rializer, the respective outputs enter TRI-STATE
chip power-on circuitry disables internal circuitry. When V
reaches V
ing to a local clock. For the Serializer, the local clock is the
transmit clock (TCLK) provided by the source ASIC or other
device. For the Deserializer, you must apply a local clock to
the REFCLK pin.
The Serializer outputs remain in TRI-STATE while the PLL
locks to the TCLK. After locking to TCLK, the Serializer is
now ready to send data or SYNC patterns, depending on the
levels of the SYNC1 and SYNC2 inputs or a data stream.
The SYNC pattern sent by the Serializer consists of six ones
and six zeros switching at the input clock rate.
Note that the Deserializer LOCK output will remain high
while its PLL locks to the incoming data or to SYNC patterns
on the input.
Step 2: The Deserializer PLL must synchronize to the Seri-
alizer to complete initialization. The Deserializer will lock to
non-repetitive data patterns. However, the transmission of
SYNC patterns enables the Deserializer to lock to the Seri-
alizer signal within a specified time. See Figure 7.
CC
OK (2.5V) the PLL in each device begins lock-
CC
to both Serializer and/or Dese-
(Continued)
®
.
®
, and on-
CC
Application
2
The user’s application determines control of the SYNC1 and
SYNC 2 pins. One recommendation is a direct feedback loop
from the LOCK pin. Under all circumstances, the Serializer
stops sending SYNC patterns after both SYNC inputs return
low.
When the Deserializer detects edge transitions at the Bus
LVDS input, it will attempt to lock to the embedded clock
information. When the Deserializer locks to the Bus LVDS
clock, the LOCK output will go low. When LOCK is low, the
Deserializer outputs represent incoming Bus LVDS data.
Data Transfer
After initialization, the Serializer will accept data from inputs
DIN0–DIN9. The Serializer uses the TCLK input to latch
incoming Data. The TCLK_R/F pin selects which edge the
Serializer uses to strobe incoming data. TCLK_R/F high
selects the rising edge for clocking data and low selects the
falling edge. If either of the SYNC inputs is high for 5*TCLK
cycles, the data at DIN0-DIN9 is ignored regardless of clock
edge.
After determining which clock edge to use, a start and stop
bit, appended internally, frame the data bits in the register.
The start bit is always high and the stop bit is always low.
The start and stop bits function as the embedded clock bits
in the serial stream.
The Serializer transmits serialized data and clock bits (10+2
bits) from the serial data output (DO
frequency. For example, if TCLK is 66 MHz, the serial rate is
66 x 12 = 792 Mega-bits-per-second. Since only 10 bits are
from input data, the serial “payload” rate is 10 times the
TCLK frequency. For instance, if TCLK = 66 MHz, the pay-
load data rate is 66 x 10 = 660 Mbps. The data source
provides TCLK and must be in the range of 40 MHz to 66
MHz nominal.
The Serializer outputs (DO
nection or in limited multi-point or multi-drop backplanes.
The outputs transmit data when the enable pin (DEN) is
high, PWRDN = high, and SYNC1 and SYNC2 are low.
When DEN is driven low, the Serializer output pins will enter
TRI-STATE.
When the Deserializer synchronizes to the Serializer, the
LOCK pin is low. The Deserializer locks to the embedded
±
) can drive a point-to-point con-
±
) at 12 times the TCLK
10093302