MXL1344ACAG+ Maxim Integrated Products, MXL1344ACAG+ Datasheet
MXL1344ACAG+
Specifications of MXL1344ACAG+
Related parts for MXL1344ACAG+
MXL1344ACAG+ Summary of contents
Page 1
... MAX3175 ________________________________________________________________ Maxim Integrated Products For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. o Certified TBR-1 and TBR-2-Compliant Chipset (NET1 and NET2)—Pending Completion of Testing o Supports V.10 (RS-423), V.11 (RS-422, RS-530, RS-530A, RS-449, V.36, and X.21), V.28 (RS-232) and V ...
Page 2
Multiprotocol, Software-Selectable Cable Terminator ABSOLUTE MAXIMUM RATINGS All Voltages to GND Unless Otherwise Noted Supply Voltages V ........................................................................-0. .........................................................................+0.3V to -7V EE Logic Input Voltages M0, M1, M2, DCE/DTE, LATCH.............................-0.3V to +6V Termination Network Inputs ...
Page 3
Multiprotocol, Software-Selectable (V = +5V -5V +25°C, unless otherwise noted V.11 OR V.35 DIFFERENTIAL-MODE IMPEDANCE vs. TEMPERATURE 106.0 105 -7V CM 105 104 +7V ...
Page 4
Multiprotocol, Software-Selectable Cable Terminator PIN NAME 1 M0 Mode-Select Pin (Table 1) Negative Supply Voltage (typically connected capacitor. 3 R1C Load 1, Center Tap 4 R1B Load 1, Node B 5 R1A Load 1, ...
Page 5
Multiprotocol, Software-Selectable 52Ω AMMETER OFF = ± 52Ω ±7V OR ± Figure 1. V.11 or V.35 Differential Impedance ...
Page 6
Multiprotocol, Software-Selectable Cable Terminator A MXL1344A R1 52Ω S1 CLOSED S2 R3 OPEN 127Ω R2 52Ω B (a) V.11 Figure 4. Termination Modes Table 1. Termination Mode Select Table DCE/ DTE PROTOCOL M2 V.10/RS-423 0 RS-530A 0 RS-530 0 ...
Page 7
Multiprotocol, Software-Selectable 4.7µF 1 CHARGE 1µF PUMP 2 1µF 5 DTE_TXD/DCE_RXD D1 6 DTE_SCTE/DCE_RXC DTE_TXC/DCE_TXC R1 9 DTE_RXC/DCE_SCTE R2 10 DTE_RXD/DCE_TXD R3 11 MXL1543 DCE/DTE ...
Page 8
Multiprotocol, Software-Selectable Cable Terminator The MXL1344A enters no-cable mode when the mode select inputs, M0, M1, and M2 are connected HIGH or left unconnected. In no-cable mode, all six termination networks are placed in V.11 mode, with S1 closed ...
Page 9
Multiprotocol, Software-Selectable GENERATOR 50Ω 125Ω 50Ω Figure 8. Typical V.35 Interface A′ R1 52Ω 52Ω B′ C′ Figure 9. V.35 Termination and Internal Resistance Networks MAX3175. With this cable wiring, the multiprotocol seri- al port is ...
Page 10
Multiprotocol, Software-Selectable Cable Terminator the V.35 receiver. Internal to the MXL1344A, S1 and S2 are closed to connect the T-network resistors to the cir- cuit. The V.35 specification allows for ±4V of ground difference between the V.35 generator and ...
Page 11
Multiprotocol, Software-Selectable A′ R1 52Ω 52Ω B′ C′ Figure 10. V.28 Termination and Internal Resistance Networks SERIAL CONTROLLER TXD SCTE TXC RXC RXD RTS DTR DCD DSR CTS LL Figure 11. DTE-to-DCE X.21 Interface ______________________________________________________________________________________ A ...
Page 12
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products ...