ADM1025ARQZ-REEL ON Semiconductor, ADM1025ARQZ-REEL Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ADM1025ARQZ-REEL
Manufacturer Part Number
ADM1025ARQZ-REEL
Description
IC MONITOR SYS/VOLT 5CH 16QSOP
Manufacturer
ON Semiconductor
Datasheet
1.ADM1025AARQ.pdf
(21 pages)
Specifications of ADM1025ARQZ-REEL
Applications
PC's, PDA's
Interface
I²C
Voltage - Supply
3 V ~ 5.5 V
Package / Case
16-QSOP
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADM1025ARQZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADM1025ARQZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Preliminary Technical Data
TEMPERATURE MEASUREMENT SYSTEM
INTERNAL TEMPERATURE MEASUREMENT
The ADM1025/ADM1025A contains an on-chip band gap
temperature sensor whose output is digitized by the on-chip
ADC. The temperature data is stored in the Local Temperature
Value Register (Address 27h). As both positive and negative
temperatures can be measured, the temperature data is stored in
twos complement format, as shown in Table 6. Theoretically,
the temperature sensor and ADC can measure temperatures
from −128°C to +127°C with a resolution of 1°C, although
temperatures below 0°C and above +100°C are outside the
operating temperature range of the device.
EXTERNAL TEMPERATURE MEASUREMENT
The ADM1025/ADM1025A can measure temperature using an
external diode sensor or diode-connected transistor connected
to Pins 9 and 10.
The forward voltage of a diode or diode-connected transistor,
operated at a constant current, exhibits a negative temperature
coefficient of about −2 mV/°C. Unfortunately, the absolute
value of V
calibration is required to null this out, so the technique is
unsuitable for mass production.
The technique used in the ADM1025/ADM1025A is to measure
the change in V
currents. This is given by:
where:
Figure 15 shows the input signal conditioning used to measure
the output of an external temperature sensor. This figure shows
the external sensor as a substrate transistor provided for
temperature monitoring on some microprocessors, but it could
equally well be a discrete transistor.
If a discrete transistor is used, the collector will not be grounded
and should be linked to the base. If a PNP transistor is used, the
base is connected to the D− input and the emitter to the D+
input. If an NPN transistor is used, the emitter is connected to
the D− input and the base to the D+ input.
Bit 6 of Status Register 2 (42h) is set if a remote diode fault is
detected. The ADM1025/ADM1025A detects shorts from D+ to
GND or supply, as well as shorts/opens between D+/D−.
is the charge on the carrier.
is the absolute temperature in Kelvins.
is Boltzmann’s constant.
is the ratio of the two currents.
Δ
BE
=
, varies from device to device, and individual
BE
/ ×
when the device is operated at two different
(
)
Rev. P5 | Page 13 of 21| www.onsemi.com
Table 6. Temperature Data Format
Temperature
−128°C
−125°C
−100°C
−75°C
−50°C
−25°C
0°C
+10°C
+25°C
+50°C
+75°C
+100°C
+125°C
+127°C
To prevent ground noise interfering with the measurement, the
more negative terminal of the sensor is not referenced to
ground but is biased above ground by an internal diode at the
D− input.
If the sensor is used in a very noisy environment, a capacitor of
value up to 1 nF may be placed between the D+ and D– inputs
to filter the noise.
To measure ΔV
currents of I and N × I. The resulting waveform is passed
through a 65 kHz low-pass filter to remove noise, then to a
chopperstabilized amplifier that performs the functions of
amplification and rectification of the waveform to produce a dc
voltage proportional to ΔV
ADC to give a temperature output in 8-bit twos complement
format. To further reduce the effects of noise, digital filtering is
performed by averaging the results of 16 measurement cycles.
An external temperature measurement takes nominally 34.8 ms.
Figure 15. Signal Conditioning for External Diode Temperature Sensors
BE
, the sensor is switched between operating
BE
. This voltage is measured by the
ADM1025/ADM1025A
Digital Output
1000 0000
1000 0011
1001 1100
1011 0101
1100 1110
1110 0111
0000 0000
0000 1010
0001 1001
0011 0010
0100 1011
0110 0100
0111 1101
0111 1111