R88M-WP20030S-BWS1 Omron, R88M-WP20030S-BWS1 Datasheet - Page 336
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-WP20030S-BWS1
Manufacturer Part Number
R88M-WP20030S-BWS1
Description
SERVO MOTOR 200W 100V W/BRAKE
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-WP20030S-BWS1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MWP20030SBWS1
- Current page: 336 of 458
- Download datasheet (5Mb)
Operation
D Limiting the Speed with Analog Voltage
• When Pn002.1 (speed command input switching) is set to 1, REF (speed command input) becomes
• Absolute REF voltage (V) / Pn300 (speed command scale) x 100 x rated rotation speed (r/min.)
• Regardless of whether the voltage is positive or negative, both forward and reverse directions have
Note The default setting is 1000 (x 0.01 V / No. or rated rotations).
4-6
Note 1. If an error occurs during the trial operation, refer to Troubleshooting to eliminate the cause.
Note 2. If the system vibrates due to insufficient gain adjustment, making it difficult to check the opera-
H Preparation for Trial Operation
Turn OFF the Power
Some parameters are enabled by turning OFF the Unit, then turning it ON again. Consequently, first turn
OFF the power to the control circuits and main circuits.
Mechanical System Connection
Firmly connect the Servomotor shaft and the load (i.e., the mechanical system). Tighten screws to make
sure they are not loose.
Absolute Encoder Setup ABS
If using Servomotor with an absolute encoder, refer to 4-2-2 Absolute Encoder Setup and Battery Chan-
ges for the setup procedure. After performing a jog operation, the amount of multi-turn rotation may be
too large, so when connecting the absolute encoder to the mechanical system, be sure to set the rota-
tion speed to zero.
4-98
Pn002.1
Pn300
Parameter No.
the analog speed limit input terminal, so you can limit the speed on multiple levels. The speed limit
value can be calculated from the following equation:
the same limits (taken as absolute values).
When you have finished installation, wiring, verifying Servomotor and Servo Driver op-
erations (i.e., jog operation), and setting the user parameters, perform a trial operation.
The main purpose of a trial operation is to confirm that the servo system is operating
correctly electrically. Make sure that the host controller and all the programming devices
are connected, then turn ON the power. First perform a trial operation at low speed to
confirm that the system is operating correctly. Next, perform a normal run pattern to con-
firm that the system is operating correctly.
Trial Operation Procedure
Then check for safety and reset the alarm, and then retry the trial operation.
tion, refer to 4-7 Making Adjustments , and adjust the gain.
Function selection
switch 2
Speed command
input switching
Speed command
scale
Parameter name
Set Pn002.1 to 1 (i.e., use REF as the analog
speed limit input).
Set the REF voltage for the rated rotation speed.
(See note.)
Explanation
4-4-4 Parameter
Details
Chapter 4
Reference
Related parts for R88M-WP20030S-BWS1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: