ISL54406IRTZ Intersil, ISL54406IRTZ Datasheet
ISL54406IRTZ
Specifications of ISL54406IRTZ
Available stocks
Related parts for ISL54406IRTZ
ISL54406IRTZ Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008, 2010. All Rights Reserved All other trademarks mentioned are the property of their respective owners +2.7V to +5.0V ...
Page 2
Pin Configurations ISL54406 10 Ld 3x3 TDFN ( TOP VIEW VDD PD 1 LOGIC SEL2 CONTROL 2 LSHUNT LOUT 3 CLICK 4 ROUT AND POP 5 GND RSHUNT NOTE: 1. ISL54406 Switches Shown for SEL1 = Logic “1” and SEL2 ...
Page 3
... Ordering Information PART NUMBER PART MARKING ISL54406IRUZ-T (Notes ISL54406IRTZ (Note 4) 4406 ISL54406IRTZ-T (Notes 2, 4) 4406 ISL54406EVAL1Z Evaluation Board NOTES: 2. Please refer to TB347 for details on reel specifications. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 4
... Maximum Junction Temperature (Plastic Package 0.3V) Maximum Storage Temperature Range -65°C to +150°C DD Pb-free reflow profile . . . . . . . . . . . . . . . . . . .see link below ) + 0.3V) http://www.intersil.com/pbfree/Pb-FreeReflow.asp DD Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . -40°C to +85°C or GND by specified amount are clamped. Limit current to DD Test Conditions ...
Page 5
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER DYNAMIC CHARACTERISTICS Turn-ON Time 2.7V 10pF, (See Figure 1) L Turn-OFF Time 2.7V, V OFF 10pF, (See Figure ...
Page 6
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER Input High Current 3.6V, V SEL2H DD I SEL1H SEL1 Pull-Down Resistor 3.6V SEL1 SEL2 Pull-Down Resistor 3.6V ...
Page 7
Test Circuits and Waveforms Repeat test for all switches /40mA ON 1 SEL1 LIN OR RIN LOUT OR 40mA ROUT GND FIGURE 2. r TEST CIRCUIT ON SIGNAL GENERATOR 0VDC TO 3VDC STEP ...
Page 8
Test Circuits and Waveforms 20kΩ Power Supply Turn-On/Turn-Off Click and Pop Transient Test *See Figure 17 8 ISL54406 (Continued) FLOAT FLOAT V SEL1 SEL2 DD LOUT LIN CLICK RIN ROUT AND POP 20kΩ GND FIGURE 6. CLICK AND POP TEST ...
Page 9
Application Block Diagram LEFT SPEAKER RIGHT SPEAKER Detailed Description The ISL54406 device is a dual single pole-single throw (SPST) analog switch that operates from a single DC power supply in the range of +2.7V to +5V. It was designed to ...
Page 10
Audio Playback Mode If the SEL1 and SEL2 pins are Logic “1”, the device will be in the Audio Playback mode. In Audio Playback mode the LIN (left) and RIN (right) 2.5Ω audio switches are connected to LOUT and ROUT ...
Page 11
Typical Performance Curves 2.61 2.60 2.59 2.58 2.57 2.56 -1.0 -0.8 -0.6 -0.4 -0 (V) OUT FIGURE 7. ON-RESISTANCE vs SWITCH VOLTAGE vs SUPPLY VOLTAGE 0.068 R = 32Ω LOAD V = 0.707V LOAD RMS 0.066 0.064 0.062 ...
Page 12
Typical Performance Curves 0 -0.5 -1.0 -1 32Ω 0.707 V IN RMS -2.0 20 100 200 500 1k FREQUENCY (Hz) FIGURE 13. INSERTION LOSS -40 -60 -80 -100 -120 -140 R ...
Page 13
Typical Performance Curves SEL2 V INL V LIN 200mV/DIV V LOUT 200mV/DIV TIME (s) 100ms/DIV FIGURE 17. 20kΩ CLICK AND POP REDUCTION Die Characteristics SUBSTRATE AND TDFN THERMAL PAD POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: 98 PROCESS: Submicron CMOS 13 ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries ...
Page 15
L10.1.8x1.4A 10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 5, 3/10 1. 0.10 2X TOP VIEW (9 X 0.60) (10X 0.20) 3 (4X 0.30 TYPICAL RECOMMENDED LAND PATTERN 15 ISL54406 6 A PIN ...
Page 16
... Dimensions D2 and E2 are for the exposed pads which provide M 0. improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Compliant to JEDEC MO-229-WEED-3 except for D2 dimensions TERMINAL TIP ( 2.90 ) MILLIMETERS ...