P87C51X2BBD NXP Semiconductors, P87C51X2BBD Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
P87C51X2BBD
Manufacturer Part Number
P87C51X2BBD
Description
MCU 8-Bit 87C 80C51 CISC 4KB EPROM 5V 44-Pin LQFP Tray
Manufacturer
NXP Semiconductors
Datasheet
1.P87C52X2BN112.pdf
(62 pages)
Specifications of P87C51X2BBD
Package
44LQFP
Device Core
80C51
Family Name
87C
Maximum Speed
33 MHz
Ram Size
128 Byte
Program Memory Size
4 KB
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Program Memory Type
EPROM
Number Of Programmable I/os
32
Interface Type
UART
Operating Temperature
0 to 70 °C
Number Of Timers
3
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P87C51X2BBD
Manufacturer:
ENE
Quantity:
14
Company:
Part Number:
P87C51X2BBD,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P87C51X2BBDЈ¬157
Manufacturer:
NXP
Quantity:
10
Philips Semiconductors
PIN DESCRIPTIONS
2003 Jan 24
V
V
P0.0-0.7
P1.0–P1.7
P2.0–P2.7
P3.0–P3.7
RST
ALE/PROG
MNEMONIC
SS
CC
80C51 8-bit microcontroller family
4K/8K/16K/32K ROM/OTP, low voltage (2.7 to 5.5 V),
low power, high speed (30/33 MHz)
39–32 43–36
21–28 24–31
10–17
DIP
1–8
20
40
10
11
12
13
14
15
16
17
30
1
2
9
PLCC
13–19
PIN NUMBER
2–9
11,
22
44
13
14
15
16
17
18
19
10
33
11
2
3
40–44,
37–30
18–25
LQFP
7–13
1–3
16
38
40
41
10
11
12
13
27
5,
5
7
8
9
4
TSSOP
28–21
30–37
10–17
1–6
29
30
31
38
19
9
1
2
3
4
5
6
TYPE NAME AND FUNCTION
I/O
I/O
I/O
I/O
I/O
O
O
O
O
I
I
I
I
I
I
I
I
I
Ground: 0 V reference.
Power Supply: This is the power supply voltage for normal, idle, and power-down
operation.
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s
written to them float and can be used as high-impedance inputs. Port 0 is also the
multiplexed low-order address and data bus during accesses to external program
and data memory. In this application, it uses strong internal pull-ups when emitting
1s. Port 0 also outputs the code bytes during program verification and received
code bytes during EPROM programming. External pull-ups are required during
program verification.
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, port 1 pins that are externally pulled low will source current
because of the internal pull-ups. (See DC Electrical Characteristics: I
receives the low-order address byte during program memory verification. Alternate
functions for Port 1 include:
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, port 2 pins that are externally being pulled low will source current
because of the internal pull-ups. (See DC Electrical Characteristics: I
emits the high-order address byte during fetches from external program memory
and during accesses to external data memory that use 16-bit addresses (MOVX
@DPTR). In this application, it uses strong internal pull-ups when emitting 1s.
During accesses to external data memory that use 8-bit addresses (MOV @Ri), port
2 emits the contents of the P2 special function register. Some Port 2 pins receive
the high order address bits during EPROM programming and verification.
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that
have 1s written to them are pulled high by the internal pull-ups and can be used as
inputs. As inputs, port 3 pins that are externally being pulled low will source current
because of the pull-ups. (See DC Electrical Characteristics: I
the special features of the 80C51 family, as listed below:
Reset: A high on this pin for two machine cycles while the oscillator is running,
resets the device. An internal diffused resistor to V
using only an external capacitor to V
Address Latch Enable/Program Pulse: Output pulse for latching the low byte of
the address during an access to external memory. In normal operation, ALE is
emitted at a constant rate of 1/6 (12-clock Mode) or 1/3 (6-clock Mode) the
oscillator frequency, and can be used for external timing or clocking. Note that one
ALE pulse is skipped during each access to external data memory. This pin is also
the program pulse input (PROG) during EPROM programming. ALE can be
disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during
a MOVX instruction.
T2 (P1.0): Timer/Counter 2 external count input/clockout (see Programmable
Clock-Out)
T2EX (P1.1): Timer/Counter 2 Reload/Capture/Direction control
RxD (P3.0): Serial input port
TxD (P3.1): Serial output port
INT0 (P3.2): External interrupt
INT1 (P3.3): External interrupt
T0 (P3.4): Timer 0 external input
T1 (P3.5): Timer 1 external input
WR (P3.6): External data memory write strobe
RD (P3.7): External data memory read strobe
10
1
1
CC
.
P80C3xX2; P80C5xX2;
SS
permits a power-on reset
IL
). Port 3 also serves
P87C5xX2
IL
IL
). Port 1 also
). Port 2
Product data