TLE7235SE Infineon Technologies, TLE7235SE Datasheet - Page 21

• Manufacturer Part Number: TLE7235SE
• Description: IC DRIVER SPI RELAY CTRL DSO20
• Manufacturer: Infineon Technologies
• Series: -r
• Type: High Side/Low Side Driverr

Specifications of TLE7235SE

• Input Type: SPI
• Number Of Outputs: 8
• On-state Resistance: 850 mOhm, 1.6 Ohm
• Current - Output / Channel: 205mA, 410mA
• Current - Peak Output: 500mA, 1A
• Voltage - Supply: 9 V ~ 16 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (0.295", 7.50mm Width)
• Packages: PG-DSO-20
• Channels: 8.0
• Rds (on) (typ): 0.85 Ohm
• Vdd: 3.0 - 5.5 V
• Vds(cl): 41.0 - 52.0 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7
The device provides embedded protective functions. Integrated protection functions are designed to prevent IC
destruction under fault conditions described in this data sheet. Fault conditions are considered as “outside” normal
operating range. Protection functions are not designed for continuous repetitive operation.
7.1
The TLE7235SE is protected in case of over load or short circuit of the load. After time
channel n switches off and the according diagnosis flag Dn is set. The channel can be switched on after clearing
the protection latch by command CMD.CPL = 1. The CPL command clears itself with the next valid SPI
communication frame. Please refer to
Figure 7
7.2
A temperature sensor for each channel causes an overheated channel to switch off to prevent destruction. The
according diagnosis flag is set. This flag is also set in OFF state, if the regarding channel temperature is too
high.The channel can be only switched on after clearing the protection latch by SPI command CMD.CPL = 1. The
CPL command clears itself with the next valid SPI communication frame. Please refer to
on Page 22
7.3
There is a designed in protection against ESD disturbances up to the specified limit by using the defined model.
Please see electrical characteristics
7.4
There is a reverse polarity protection implemented in the TLE7235SE. This protection has to be divided into two
parts. First the protection of the control circuits and second in the protection of the power transistors.
The control circuits are reverse polarity protected by protective measures in the ground connection. In case of
reverse polarity, there is no current flow through the control circuits.
The power transistors contain intrinsic body diodes that cause power dissipation. The reverse current through
these intrinsic body diodes has to be limited by the connected loads. The over temperature and over load
protection are not active during reverse polarity.
7.5
In case of loss of
additional path from
suppressor diode like in the application diagram (see D1 in
Data Sheet
for information on diagnosis features.
Protection Functions
Over Load Protection
Shut Down at Over Load
Over Temperature Protection
ESD protection
Reverse Polarity Protection
Loss of V
V
bb
V
connection in on-state, all inductances of the loads have to be demagnetized through the an
bb
I
D0(OV L)
to ground. Usually this path is given somewhere in the PCB circuitry, for example, as a
I
bb
IN
D0
t
OFF(OV L)
“ESD susceptibility on all pins” on Page 11
Figure 7
D0 = 1
b
for details.
20
CPL = 1
D0 = 00
Figure 14 “Application Diagram” on Page
SPI Driver for Enhanced Relay Control
b
b
t
t
OverLoad.emf
t
OFF(OVL)
“Diagnostic Features”
Protection Functions
Rev. 1.1, 2011-04-05
, the over loaded
TLE7235SE
34).