ADG333ABNZ Analog Devices Inc, ADG333ABNZ Datasheet - Page 11

• Manufacturer Part Number: ADG333ABNZ
• Description: IC SWITCH QUAD SPDT 20DIP
• Manufacturer: Analog Devices Inc
• Type: Analog Switchr

Specifications of ADG333ABNZ

• Function: Switch
• Circuit: 4 x SPDT
• On-state Resistance: 45 Ohm
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 12V
• Current - Supply: 0.01µA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 20-DIP (0.300", 7.62mm)
• Analog Switch Type: SPDT
• No. Of Channels: 4
• On State Resistance Max: 45ohm
• Turn Off Time: 80ns
• Turn On Time: 90ns
• Supply Voltage Range: 3V To 30V
• Operating Temperature Range: -40°C To +85°C
• Multiplexer Configuration: Quad SPDT
• Number Of Inputs: 4
• Number Of Outputs: 8
• Number Of Channels: 4
• Analog Switch On Resistance: 45@±15VOhm
• Analog Switch Turn On Time: 110ns
• Analog Switch Turn Off Time: 100ns
• Package Type: PDIP N
• Power Supply Requirement: Single/Dual
• Single Supply Voltage (min): 3V
• Single Supply Voltage (typ): 12V
• Single Supply Voltage (max): 30V
• Dual Supply Voltage (min): ±3V
• Dual Supply Voltage (typ): ±5/±9/±12/±15V
• Dual Supply Voltage (max): ±20V
• Power Dissipation: 3.77mW
• Supply Current: 0.25@±15VmA
• Mounting: Through Hole
• Pin Count: 20
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Package: 20PDIP N
• Maximum On Resistance: 45@±15V Ohm
• Maximum High Level Output Current: 20 mA
• Maximum Turn-off Time: 100(Typ)@12V ns
• Maximum Turn-on Time: 110(Typ)@12V ns
• Switch Architecture: SPDT
• Power Supply Type: Single|Dual
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

APPLICATION INFORMATION
ADG333A SUPPLY VOLTAGES
The ADG333A can operate from a dual or signal supply. V
should be connected to GND when operating with a single
supply. When using a dual supply, the ADG333A can also
operate with unbalanced supplies; for example V
V
exceed 30 V, V
to V
the ADG333A supply voltage directly affects the input signal
range, the switch on resistance and the switching times of the
part. The effects of the power supplies on these characteristics
can be clearly seen from the Typical Performance Characteristics
curves.
SS
= −5 V. The only restrictions are that V
SS
must not exceed +44 V. It is important to remember that
SS
to GND must not drop below −30 V, and V
DD
to GND must not
DD
= 20 V and
SS
DD
Rev. A | Page 11 of 12
POWER SUPPLY SEQUENCING
When using CMOS devices, care must be taken to ensure
correct power-supply sequencing. Incorrect power-supply
sequencing can result in the device being subjected to stresses
beyond those listed in the Absolute Maximum Ratings. This is
also true for the ADG333A. Always turn on V
by V
mum specified ratings can then be safely presented to the source
or drain of the switch
SS
and the logic signals. An external signal within the maxi-
DD
first, followed
ADG333A