MC145406DW Freescale Semiconductor, MC145406DW Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
MC145406DW
Manufacturer Part Number
MC145406DW
Description
Manufacturer
Freescale Semiconductor
Datasheet
1.MC145406DW.pdf
(12 pages)
Specifications of MC145406DW
Number Of Receivers
3
Number Of Transmitters
3
Number Of Transceivers
1
Data Transmission Topology
Point-to-Point
Receiver Signal Type
Single-Ended
Transmitter Signal Type
Single-Ended
Single Supply Voltage (typ)
Not RequiredV
Single Supply Voltage (min)
Not RequiredV
Single Supply Voltage (max)
Not RequiredV
Dual Supply Voltage (min)
±4.5/4.5V
Dual Supply Voltage (max)
±13.2/5.5V
Power Supply Requirement
Triple
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
16
Package Type
SOIC W
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC145406DW
Manufacturer:
N/A
Quantity:
20 000
Company:
Part Number:
MC145406DWR2G
Manufacturer:
ON
Quantity:
4 300
specifications of standards EIA 232–E and CCITT V.28.
EIA 232–E defines the electrical and physical interface be-
tween Data Communication Equipment (DCE) and Data
Terminal Equipment (DTE). A DCE is connected to a DTE
using a cable that typically carries up to 25 leads. These
leads, referred to as interchange circuits, allow the transfer
of timing, data, control, and test signals. Electrically this
transfer requires level shifting between the TTL/CMOS log-
ic levels of the computer or modem and the high voltage lev-
els of EIA 232–E, which can range from
MC145406 provides the necessary level shifting as well as
meeting other aspects of the EIA 232–E specification.
DRIVERS
ents a voltage of between
tween 3 to 7 k . A logic 1 at the driver input results in a
voltage of between – 5 to – 15 V. A logic 0 results in a voltage
between + 5 to + 15V. When operating V DD and V SS at 7 to
ing at
EIA 232–E specification. However, the output voltages when
using a
and can be used in applications where strict compliance to
EIA 232–E is not required.
they withstand a short to another driver in the EIA 232–E
cable. The worst–case condition that is permitted by
EIA 232–E is a
mA. The MC145406 drivers can withstand this condition
momentarily. In most short circuit conditions the source
driver will have a series 300
to satisfy the EIA 232–E driver requirements. This will re-
duce the short circuit current to under 40 mA which is an
acceptable level for the MC145406 to withstand.
an internally–limited output slew–rate that does not exceed
30 V per s.
RECEIVERS
in the range of – 25 to + 25 V down to TTL/CMOS logic lev-
els (0 to + 5 V). A voltage of between – 3 and – 25 V on Rx1
is defined as a mark and produces a logic 1 at DO1. A volt-
age between + 3 and + 25 V is a space and produces a logic
zero. While receiving these signals, the Rx inputs must pres-
ent a resistance between 3 and 7 k . Nominally, the input re-
sistance of the Rx1–Rx3 inputs is 5.4 k .
biased at 1.8 V above ground (GND) with typically 800 mV of
hysteresis included to improve noise immunity. The 1.8 V
MOTOROLA
12 V, the MC145406 meets this requirement. When operat-
5 V at the output (when terminated), which does not meet
4 V) to permit proper reception by an EIA 232–E receiver,
The MC145406 has been designed to meet the electrical
As defined by the specification, an EIA 232–E driver pres-
Another requirement of the MC145406 drivers is that
Unlike some other drivers, the MC145406 drivers feature
The job of an EIA 232–E receiver is to level–shift voltages
The input threshold of the Rx1–Rx3 inputs is typically
5 V, the MC145406 drivers produce less than
5 V power supply are high enough (around
15 V source that is current limited to 500
5 to
output impedance needed
15 V into a load of be-
3 to
APPLICATIONS INFORMATION
25 V. The
bias forces the appropriate DO pin to a logic 1 when its Rx
input is open or grounded as called for in the EIA 232–E
specification. Notice that TTL logic levels can be applied to
the Rx inputs in lieu of normal EIA 232–E signal levels. This
might be helpful in situations where access to the modem or
computer through the EIA 232–E connector is necessary
with TTL devices. However, it is important not to connect the
EIA 232–E outputs (Tx1–Tx3) to TTL inputs since TTL oper-
ates off + 5 V only, and may be damaged by the high output
voltage of the MC145406.
input (such as an input to a modem chip). These outputs
will swing from V CC to ground, allowing the designer to op-
erate the DO and DI pins from digital power supply. The Tx
and Rx sections are independently powered by V DD and
V SS so that one may run logic at + 5 V and the EIA 232–E
signals at
POWER SUPPLY CONSIDERATIONS
device current.
through an internal diode from the V CC pin to the V DD pin
when V DD < V CC by approximately 0.6 V. This high current
condition can exist for a short period of time during power
up/down. Additionally, if the + 12 V supply is switched off
while the + 5 V is on and the off supply is a low impedance
to ground, the diode D1 will prevent current flow through
the internal diode.
from drifting positive to V CC , in the event that power is re-
moved from V SS (Pin 12). If V SS power is removed, and the
impedance from the V SS pin to ground is greater than
approximately 3 k , this pin will be pulled to V CC by internal
circuitry causing excessive current in the V CC pin.
to exist, then the diodes D1 and D2 are not required.
ESD PROTECTION
ble to the outside world is essential. High static voltages ap-
plied to the pins when someone touches them either directly
or indirectly can cause damage to gate oxides and transistor
junctions by coupling a portion of the energy from the I/O pin
to the power supply buses of the IC. This coupling will usually
occur through the internal ESD protection diodes. The key to
protecting the IC is to shunt as much of the energy to ground
as possible before it enters the IC. Figure 4 shows a tech-
nique which will clamp the ESD voltage at approximately
appears on the supply pins is shunted to ground through the
capacitors C1–C3. This scheme has provided protection to
the interface part up to
test.
15 V using the MMVZ15VDLT1. Any residual voltage which
The DO outputs are to be connected to a TTL or CMOS
Figure 4 shows a technique to guard against excessive
The diode D1 prevents excessive current from flowing
The diode D2 is used as a voltage clamp, to prevent V SS
If by design, neither of the above conditions are allowed
ESD protection on IC devices that have their pins accessi-
12 V.
10 kV, using the human body model
MC145406
5