PDIUSBH11AD NXP Semiconductors, PDIUSBH11AD Datasheet
PDIUSBH11AD
Specifications of PDIUSBH11AD
Available stocks
Related parts for PDIUSBH11AD
PDIUSBH11AD Summary of contents
Page 1
PDIUSBH11A Universal Serial Bus Hub Product specification Supersedes data of 1998 Jun 04 hilips Semiconductors INTEGRATED CIRCUITS 1999 Jul 22 ...
Page 2
Philips Semiconductors Universal Serial Bus Hub FEATURES Complies with the Universal Serial Bus specification Rev. 1.0 Complies with the ACPI, OnNOW, and USB power management requirements Compliant with USB Human Interface Devices and Monitor Control Class Compliant with System Management ...
Page 3
Philips Semiconductors Universal Serial Bus Hub BLOCK DIAGRAM UPSTREAM PORT 3.3V D+ 1.5k D+ SoftConnect ANALOG HUB REPEATER ANALOG GOODLINK ANALOG GOODLINK CONTROL CONTROL D– LED D+ ...
Page 4
Philips Semiconductors Universal Serial Bus Hub Analog Transceivers These transceivers interface directly to the USB cables through some termination resistors. They are capable of transmitting and receiving serial data at both “full speed” (12 Mbit/s) and “low speed” (1.5 Mbit/s) ...
Page 5
Philips Semiconductors Universal Serial Bus Hub ENDPOINT DESCRIPTIONS There are two endpoint configuration modes supported by the PDIUSBH11A, the Single Embedded Function mode and the Multiple (3) Embedded Function mode. The Single Embedded Function mode is the default at power ...
Page 6
Philips Semiconductors Universal Serial Bus Hub PIN DESCRIPTION The PDIUSBH11A has two modes of operation. The first mode (Mode 0) configures the pins DNx_GL_N for GoodLink LED indication. The second mode (Mode 1) configures the LED pins as per port ...
Page 7
Philips Semiconductors Universal Serial Bus Hub Pin description (MODE 0 – Good Link ) PIN NO PIN SYMBOL TYPE 1 TEST1 Input 2 TEST2 Input 3 TEST3 Input 4 RESET_N Input 5 GND Power 6 XTAL1 Input 7 XTAL2 Output ...
Page 8
Philips Semiconductors Universal Serial Bus Hub Pin description (MODE 1 – Individual Overcurrent) PIN NO PIN SYMBOL TYPE 1 TEST1 Input 2 TEST2 Input 3 TEST3 Input 4 RESET_N Input 5 GND Power 6 XTAL1 Input 7 XTAL2 Output 8 ...
Page 9
Philips Semiconductors Universal Serial Bus Hub APPLICATION DIAGRAM 3.3V 5V POWER SWITCH AND OVERCURRENT CIRCUIT Interface 2 The I C bus is used to interface to an external microcontroller needed to control the operation of the hub. ...
Page 10
Philips Semiconductors Universal Serial Bus Hub COMMAND SUMMARY Some commands have the same command code (e.g., Read Buffer and Write Buffer). In these cases, the direction of the Data Phase (read or write) indicates which command is executed. COMMAND NAME ...
Page 11
Philips Semiconductors Universal Serial Bus Hub COMMAND DESCRIPTIONS Command Procedure There are four basic types of commands: Initialization, Data, Hub Specific, and General commands. Respectively, these are used to initialize the hub and embedded function; for data flow between the ...
Page 12
Philips Semiconductors Universal Serial Bus Hub Set Mode Command : F3h Data : Write 2 bytes The Set Mode command is followed by two data writes. The first byte contains the configuration byte values. The second byte is the clock ...
Page 13
Philips Semiconductors Universal Serial Bus Hub Data Flow Commands Data flow commands are used to manage the data transmission between the USB endpoints and the monitor. Much of the data flow is initiated via an interrupt to the microcontroller. The ...
Page 14
Philips Semiconductors Universal Serial Bus Hub Table 3. ERROR CODES ERROR RESULT CODE 0000 No Error PID encoding Error; bits 7–4 are not the inversion of 0001 bits 3–0 PID unknown; encoding is valid, but PID does not 0010 exist ...
Page 15
Philips Semiconductors Universal Serial Bus Hub Set Endpoint Status Command : 40–4Dh Data : Write 1 byte A stalled control endpoint is automatically unstalled when it receives a SETUP token, regardless of the content of the packet. If the endpoint ...
Page 16
Philips Semiconductors Universal Serial Bus Hub Get Port Status Command : E0h–E3h Data : Read bytes The Get Port Status Command can be followed by one or two data reads. The first byte returned contains the port ...
Page 17
Philips Semiconductors Universal Serial Bus Hub General Commands Send Resume Command : F6h Data : None Sends an upstream resume signal for 10 ms. This command is normally issued when the device is in suspend. The RESUME command is not ...
Page 18
Philips Semiconductors Universal Serial Bus Hub RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER V DC supply voltage input voltage range input voltage range for I/O I input voltage range for analog I/O AI/O V ...
Page 19
Philips Semiconductors Universal Serial Bus Hub DC CHARACTERISTICS (Digital pins) SYMBOL PARAMETER Input Levels V LOW level input voltage IL V HIGH level input voltage IH V LOW to HIGH threshold voltage TLH V HIGH to LOW threshold voltage THL ...
Page 20
Philips Semiconductors Universal Serial Bus Hub AC CHARACTERISTICS (AI/O pins, FULL speed) SYMBOL PARAMETER Driver characteristics Transition Time: t Rise time R t Fall time F t Rise/fall time matching RFM V Output signal crossover voltage CRS Driver Timings t ...
Page 21
Philips Semiconductors Universal Serial Bus Hub t PERIOD CROSSOVER POINT DIFFERENTIAL DATA LINES DIFFERENTIAL DATA TO SEO/EOP SKEW Figure 1. Differential data to EOP transition skew and EOP width V DD CROSSOVER POINT UPSTREAM- DIFFERENTIAL DATA V ...
Page 22
Philips Semiconductors Universal Serial Bus Hub V DD UPSTREAM- DIFFERENTIAL DATA EOP– DOWNSTREAM- DIFFERENTIAL DATA DOWNSTREAM EOP DELAY EOP DELAY EOPD EOP DELAY RELATIVE EOPDR EOP ...
Page 23
Philips Semiconductors Universal Serial Bus Hub 2 AC CHARACTERISTICS ( I C pins) All timing values are valid within the operating supply voltage and ambient temperature range and reference to V swing of V and SYMBOL ...
Page 24
Philips Semiconductors Universal Serial Bus Hub SO32: plastic small outline package; 32 leads; body width 7.5mm 1999 Jul 22 24 Product specification PDIUSBH11A SOT287-1 ...
Page 25
Philips Semiconductors Universal Serial Bus Hub SDIP32: plastic shrink dual in-line package; 32 leads (400 mil) 1999 Jul 22 25 Product specification PDIUSBH11A SOT232-1 ...
Page 26
Philips Semiconductors Universal Serial Bus Hub SOLDERING Introduction This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number ...
Page 27
Philips Semiconductors Universal Serial Bus Hub SUITABILITY OF IC PACKAGES FOR WAVE, REFLOW AND DIPPING SOLDERING METHODS Mo nting Mounting Package Package Through-hole mount DBS, DIP, HDIP, SDIP, SIL BGA, SQFP, HLQFP, HSQFP, HSOP, SMS Surface mount PLCC, SO, SOJ ...
Page 28
Philips Semiconductors Universal Serial Bus Hub Purchase of Philips I to use the components in the specifications defined by Philips. This specification can be ordered using the code 9398 393 40011. Data sheet status Data sheet ...