E28F016SA-100 Intel, E28F016SA-100 Datasheet - Page 5

• Manufacturer Part Number: E28F016SA-100
• Manufacturer: Intel

Specifications of E28F016SA-100

• Density: 16Mb
• Access Time (max): 100ns
• Interface Type: Parallel
• Boot Type: Not Required
• Address Bus: 21/20Bit
• Operating Supply Voltage (typ): 3.3/5V
• Operating Temp Range: 0C to 70C
• Package Type: TSOP
• Program/erase Volt (typ): 11.4 to 12.6V
• Sync/async: Asynchronous
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 3/4.5V
• Operating Supply Voltage (max): 3.6/5.5V
• Word Size: 8/16Bit
• Number Of Words: 2M/1M
• Supply Current: 60mA
• Mounting: Surface Mount
• Pin Count: 56
• Lead Free Status / Rohs Status: Not Compliant

1.0
The documentation of the Intel 28F016SA memory
device includes this datasheet, a detailed user’s
manual, and a number of application notes, all of
which are referenced at the end of this datasheet.
The datasheet is intended to give an overview of the
chip feature-set and of the operating AC/DC
specifications. The 16-Mbit Flash Product Family
User’s Manual provides complete descriptions of
the user modes, system interface examples and
detailed descriptions of all principles of operation. It
also contains the full list of software algorithm
flowcharts, and a brief section on compatibility with
Intel 28F008SA.
1.1
The 28F016SA is a high-performance 16-Mbit
(16,777,216 bit) block erasable nonvolatile random
access memory organized as either 1 Mword x
16 or 2 Mbyte x 8. The 28F016SA includes thirty-
two 64-KB (65,536) blocks or thirty-two 32-KW
(32,768) blocks. A chip memory map is shown in
Figure 4.
The implementation of a new architecture, with
many enhanced features, will improve the device
operating characteristics and results in greater
product reliability and ease-of-use.
Among the significant enhancements on the
28F016SA:
A 3/5# input pin reconfigures the device internally
for optimized 3.3V or 5.0V read/program operation.
The 28F016SA will be available in a 56-lead,
1.2 mm thick, 14 mm x 20 mm TSOP type I
package or a 56-lead, 1.8 mm thick, 16 mm x
23.7 mm SSOP package. The TSOP form factor
and pinout allow for very high board layout
densities. SSOP packaging provides relaxed lead
spacing dimensions.
A Command User Interface (CUI) serves as the
system interface between the microprocessor or
microcontroller and the internal memory operation.
SEE NEW DESIGN RECOMMENDATIONS
3.3V Low Power Capability
Improved Program Performance
Dedicated Block Program/Erase Protection
INTRODUCTION
Product Overview
Internal algorithm automation allows word/byte
programs and block erase operations to be
executed using a two-write command sequence to
the CUI in the same way as the 28F008SA 8-Mbit
FlashFile memory.
A superset of commands have been added to the
basic 28F008SA command-set to achieve higher
program
capabilities. These new commands and features
include:
Writing of memory data is performed in either byte
or word increments typically within 6 µs, a 33%
improvement over the 28F008SA. A block erase
operation erases one of the 32 blocks in typically
0.6 sec, independent of the other blocks, which is a
65% improvement over the 28F008SA.
Each block can be written and erased a minimum of
100,000 cycles. Systems can achieve typically one-
million block erase cycles by providing wear-leveling
algorithms and graceful block retirement. These
techniques have already been employed in many
flash file systems. Additionally, wear leveling of
block erase cycles can be used to minimize the
program/erase
blocks.
The 28F016SA incorporates two Page Buffers of
256 bytes (128 words) each to allow page data
writes. This feature can improve a system write
performance by up to 4.8 times over previous flash
memory devices.
All operations are started by a sequence of
command writes to the device. Three Status
Registers (described in detail later) and a RY/BY#
output pin provide information on the progress of
the requested operation.
While the 28F008SA requires an operation to
complete before the next operation can be
requested, the 28F016SA allows queueing of the
next operation while the memory executes the
current operation. This eliminates system overhead
Page Buffer Writes to Flash
Command Queueing Capability
Automatic Data Programs during Erase
Software Locking of Memory Blocks
Two-Byte
Systems
Erase All Unlocked Blocks
performance
Successive
performance
and
Programs
differences
provide
28F016SA
additional
in
across
8-bit
5