5962-8972401RA E2V, 5962-8972401RA Datasheet
5962-8972401RA
Specifications of 5962-8972401RA
Available stocks
Related parts for 5962-8972401RA
5962-8972401RA Summary of contents
Page 1
... LTR A Changes in accordance with NOR 5962-R017-92. B Update to current requirements. Editorial changes throughout. - gap The original first page of this drawing has been replaced. REV SHEET REV SHEET REV STATUS REV OF SHEETS SHEET PMIC N/A PREPARED BY STANDARD CHECKED BY Tim H. Noh MICROCIRCUIT DRAWING APPROVED BY William K ...
Page 2
... See MIL-STD-1835 JC ) ........................................ -55°C to +125° and must withstand the added SIZE A X Lead finish (see 1.2.3) Circuit function Octal D flip-flop with three-state outputs Package style dual-in-line flat square chip carrier CC due to short-circuit output test; e.g 5962-89724 REVISION LEVEL SHEET ...
Page 3
... These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL- PRF-38535 is required to identify when the QML flow option is used. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR (H)): W (L)): W http://assist.daps.dla.mil;quicksearch/ SIZE A or www.dodssp.daps.mil or from the 5962-89724 REVISION LEVEL SHEET B 3 ...
Page 4
... In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “ ...
Page 5
... OUT OUT OUT See 4.3.1c SIZE A Group A Limits subgroups Min Max 2 100 -0 - -60 -150 110 10, 11 100 7, 8 5962-89724 REVISION LEVEL SHEET B 5 Unit µA µA mA µA µ MHz ...
Page 6
... Group A Limits subgroups Min Max 9 4.0 8.5 10, 11 3.0 9.5 9 4.0 8.5 10, 11 3.0 9.5 9 2.5 8.0 10, 11 2.0 9.0 9 3.0 8.5 10, 11 3.0 9.5 9 1.0 6.0 10, 11 1.0 7.0 9 1.0 5.5 10, 11 1.0 6.0 5962-89724 REVISION LEVEL SHEET B 6 Unit ...
Page 7
... STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 Case outlines R, S, and 2 Terminal Terminal symbols number GND FIGURE 1. Terminal connections. SIZE A REVISION LEVEL 5962-89724 SHEET B 7 ...
Page 8
... X Z FIGURE 2. Truth table. Switch position Test Switch t Closed PLZ t Closed PZL All others Open FIGURE 3. Test circuit and switching waveforms. SIZE A Operating mode Load and read register Load and read register Hold Disable outputs Disable outputs 5962-89724 REVISION LEVEL SHEET B 8 ...
Page 9
... The outputs are measured one at a time with one input transition per measurement. FIGURE 3. Test circuit and switching waveforms - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 of pulse generator. OUT = t = 2.5 ns, duty cycle = SIZE A REVISION LEVEL B 5962-89724 SHEET 9 ...
Page 10
... SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547 ...
Page 11
... DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. Standard microcircuit drawing PIN 1/ 5962-8972401RA 5962-8972401SA 5962-89724012A 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. ...