AM29LV001BB-90EC Spansion Inc., AM29LV001BB-90EC Datasheet - Page 38

• Manufacturer Part Number: AM29LV001BB-90EC
• Manufacturer: Spansion Inc.

Specifications of AM29LV001BB-90EC

• Cell Type: NOR
• Density: 1Mb
• Access Time (max): 90ns
• Interface Type: Parallel
• Boot Type: Bottom
• Address Bus: 17b
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: 0C to 70C
• Package Type: TSOP
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Asynchronous
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 128K
• Supply Current: 12mA
• Mounting: Surface Mount
• Pin Count: 32
• Lead Free Status / Rohs Status: Not Compliant

ERASE AND PROGRAMMING PERFORMANCE
Notes:
1. Typical program and erase times assume the following conditions: 25×C, 3.0 V VCC, 1,000,000 cycles. Additionally,
2. Under worst case conditions of 90°C, VCC = 2.7 V (3.0 V for -45R), 1,000,000 cycles.
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See
6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
LATCHUP CHARACTERISTICS
Includes all pins except V
TSOP PIN CAPACITANCE
Notes:
1. Sampled, not 100% tested.
2. Test conditions T
PLCC PIN CAPACITANCE
Notes:
1. Sampled, not 100% tested.
2. Test conditions T
36
Sector Erase Time
Chip Erase Time
Byte Programming Time
Chip Programming Time (Note 3)
Input voltage with respect to V
(including A9, OE#, and RESET#)
Input voltage with respect to V
V
Parameter Symbol
CC
programming typicals assume checkerboard pattern.
program faster than the maximum program times listed.
Table 5 on page 17
Parameter
Current
Symbol
C
C
C
OUT
IN2
C
C
IN
C
OUT
IN2
IN
Parameter
A
A
= 25°C, f = 1.0 MHz.
= 25°C, f = 1.0 MHz.
for further information on command definitions.
CC
Input Capacitance
Output Capacitance
Control Pin Capacitance
Control Pin Capacitance
Parameter Description
. Test conditions: V
Description
Output Capacitance
Input Capacitance
Parameter Description
SS
SS
on all pins except I/O pins
on all I/O pins
Typ (Note 1)
CC
0.7
1.1
7
9
= 3.0 V, one pin at a time.
D A T A S H E E T
Am29LV001B
Max (Note 2)
300
3.3
15
V
V
V
OUT
IN
PP
Test Setup
V
= 0
V
V
OUT
= 0
Test Setup
IN
IN
= 0
= 0
= 0
= 0
–100 mA
–1.0 V
–1.0 V
Min
Unit
µs
s
s
s
Excludes 00h programming
prior to erasure (Note 4)
Excludes system level
overhead (Note 5)
Typ
Typ
8.5
7.5
4
8
8
6
21557F4 May 5, 2006
Comments
VCC + 1.0 V
Max
+100 mA
Max
12
7.5
12
12
13.0 V
6
9
Max
Unit
Unit
pF
pF
pF
pF
pF
pF