S5920Q Applied Micro Circuits Corporation, S5920Q Datasheet - Page 147

• Manufacturer Part Number: S5920Q
• Manufacturer: Applied Micro Circuits Corporation

Specifications of S5920Q

• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Operating Temperature (max): 70C
• Package Type: PQFP
• Rad Hardened: No
• Lead Free Status / Rohs Status: Not Compliant

S5920 – PCI Product: Pass-Thru Operation
After the host reads all Base Address Registers in the
system (as every PCI device implements from one to
six), the PCI BIOS allocates memory and I/O space to
each Base Address region. The host then writes the
start address of each region back into the Base
Address Registers. The start address of a region is
always an integer multiple of the region size. For
example, a 64-Kbyte memory region is always
mapped to begin on a 64K boundary in memory. It is
important to note that no PCI device can be absolutely
located in system memory or I/O space. All mapping is
determined by the system, not the application.
PCI or Add-On Operation registers PTCR or APTCR
provide additional configuration control for each
region.
Accessing a Pass-Thru Region
After the system is finished defining all Base Address
Regions within a system, each Base Address Register
contains a physical address. The application software
must now find the location in memory or I/O space of
its hardware. PCI systems provide BIOS or operating
system function calls for application software to find
particular devices on the PCI bus based on Vendor ID
and Device ID values. This allows application software
to access the device’s Configuration Registers.
The Base Address Register values in the S5920’s
Configuration Space may then be read and stored for
use by the program to access application hardware.
The value in the Base Address Registers is the physi-
cal address of the first location of that Pass-Thru
region. Some processor architectures allow this
address to be used directly to access the PCI device.
For Intel Architecture systems, the physical address
must be changed into a Segment/Offset combination.
For Real Mode operation in an Intel Architecture sys-
tem (device mapped below 1 Mbyte in memory),
creating a Segment/Offset pair is relatively simple. To
calculate a physical address, the CPU shifts the seg-
ment register 4 bits to the left and adds the offset
(resulting in a 20 bit physical address). The value in
the Base Address Register must be read and shifted 4
bits to the right. This is the segment value and should
be stored in one of the Segment registers. An offset of
zero (stored in SI, DI or another offset register)
accesses the first location in the Pass-Thru region.
Special Programming Features
A few additional features have been provided to the
user which will allow for optimal “tuning” of their sys-
tem. As these are not features that will be changed “on
the fly”, they have been included as part of the nvRAM
boot-up sequence. nvRAM address 45h is a memory
AMCC Confidential and Proprietary
location in the external nvRAM which will contain
these custom programmed bits. These features, and
their corresponding bit at location 45h, are described
as follows:
Target Latency describes the number of cycles that a
target device may respond to a PCI data transfer
request. The PCI 2.1 specification indicates that the
target device has 16 clocks to respond to an initial
request (from the assertion of FRAME#), and 8 clocks
from each subsequent data phase. If the target is not
capable of asserting TRDY# within these time frames,
it must assert a STOP#, thus initiating a disconnect.
The Target Latency programmed bit allows the user to
disable the generation of disconnects in the event of a
slow Add-On device.
If Target Latency Enb is low, target latency is ignored.
In this case, the S5920 will never issue a retry/discon-
nect in the event of a slow add-on device. Instead,
TRDY# wait states will be asserted. This might be use-
ful for an embedded system, where the S5920 can
take up as many clock cycles as necessary to com-
plete a transfer. This programmable bit is only
provided for flexibility and most users should leave this
bit set to 1. If Target Latency Enb is high, the device
will be PCI 2.1 compliant with respect to Target
Latency.
Retry Flush Enb indicates to the Pass-Thru whether to
hold prefetched data following a disconnect, or to
allow the data to be flushed out during the next PCI
read access. If low, the data will be held in the PT read
FIFO until the initiator comes back to read it out. All
subsequent PCI accesses to the S5920 from a device
other than the one who initiated the read will be
acknowledged with a retry. If the master never returns
for the data, the Pass-Thru function will be hung. Even
though the PCI 2.1 Specification does not require a
master to return for data following a disconnect, it is
unlikely that a master will terminate a read transfer
until all data has been collected.
If Retry Flush Enb is high, the data will be flushed from
the FIFO if a subsequent PCI read access is not to the
same address. If the original master received a retry
LOC_45(h)
b = (7:3)
b = 0
b = 1
b = 2
Target Latency Enb
Write FIFO Mode
Retry Flush Enb
Revision 1.02 – April 12, 2007
Description
Reserved
Data Book
DS1596
Default
1
0
0
x
147