IS42S16100A1-7T ISSI, Integrated Silicon Solution Inc, IS42S16100A1-7T Datasheet - Page 33

no-image

IS42S16100A1-7T

Manufacturer Part Number
IS42S16100A1-7T
Description
Manufacturer
ISSI, Integrated Silicon Solution Inc
Type
SDRAMr
Datasheet

Specifications of IS42S16100A1-7T

Organization
1Mx16
Density
16Mb
Address Bus
12b
Access Time (max)
6/5.5ns
Maximum Clock Rate
143MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
130mA
Pin Count
50
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / Rohs Status
Not Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
IS42S16100A1-7T
Manufacturer:
ISSI
Quantity:
503
Part Number:
IS42S16100A1-7TL
Manufacturer:
ISSI
Quantity:
16
IS42S16100A1
Write Cycle (Full Page) Interruption Using
the Burst Stop Command
The IS42S16100A1 can input data continuously from the
burst start address (a) to location a+255 during a write
cycle in which the burst length is set to full page. The
IS42S16100A1 repeats the operation starting at the
256th cycle with data input returning to location (a) and
continuing with a+1, a+2, a+3, etc. A burst stop
command must be executed to terminate this cycle. A
precharge command
Integrated Silicon Solution, Inc. — www.issi.com —
Rev. C
08/12/03
Burst Data Interruption Using the U/LDQM
Pins (Read Cycle)
Burst data output can be temporarily interrupted (masked)
during a read cycle using the U/LDQM pins. Regardless of
the CAS latency, two clock cycles (t
LDQM pins goes HIGH, the corresponding outputs go to the
HIGH impedance state. Subsequently, the outputs are
maintained in the high impedance state as long as that U/
LDQM pin remains HIGH. When the U/LDQM pin goes
LOW, output is resumed at a time t
CAS latency = 2, burstlength = 4
COMMAND
COMMAND
CLK
DQ8-DQ15
DQ
DQ0-DQ 7
UDQM
LDQM
READ (CA=A, BANK 0)
CLK
WRITE A0
D
IN
READ (CA=A, BANK 0)
A0
READ A0
QMD
QMD
D
) after one of the U/
DATA MASK (UPPER BYTE)
IN
later. This output
A1
D
IN
t
DATA MASK (LOWER BYTE)
QMD=2
D
D
A
OUT
OUT
1-800-379-4774
A0
A0
D
IN
must be executed within the ACT to PRE command
period (t
After the period (t
stop following the execution of the burst stop command
has elapsed, the write cycle terminates. This period
(t
latency.
control operates independently on a byte basis with the
UDQM pin controlling upper byte output (pins
DQ8-DQ15) and the LDQM pin controlling lower byte output
(pins DQ0 to DQ7).
Since the U/LDQM pins control the device output buffers
only, the read cycle continues internally and, in particular,
incrementing of the internal burst counter continues.
D
A1
WBD
OUT
HI-Z
) is zero clock cycles, regardless of the CAS
A1
D
RAS
IN
D
A2
OUT
max.) following the burst stop command.
HI-Z
BURST STOP
A2
WBD
BST
INVALID DATA
D
) required for burst data input to
t
WBD=0
OUT
A3
PRECHARGE (BANK 0)
PRE 0
HI-Z
t
RP
ISSI
Don't Care
33
®

Related parts for IS42S16100A1-7T