5962-9305702MPA Linear Technology, 5962-9305702MPA Datasheet - Page 4

• Manufacturer Part Number: 5962-9305702MPA
• Manufacturer: Linear Technology

Specifications of 5962-9305702MPA

• Lead Free Status / Rohs Status: Not Compliant

DSCC FORM 2234
APR 97
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
tests for each subgroup are defined in table I.
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
DEPARTMENT OF DEFENSE SPECIFICATION
DEPARTMENT OF DEFENSE STANDARDS
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
MIL-STD-883
MIL-STD-1835 -
MIL-HDBK-103 -
MIL-HDBK-780 -
(Copies of these documents are available online at
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
STANDARD
-
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
http://assist.daps.dla.mil/quicksearch/
SIZE
A
REVISION LEVEL
B
or
http://assist.daps.dla.mil
SHEET
5962-93057
4
or