MAX9671CTH+T Maxim Integrated Products, MAX9671CTH+T Datasheet - Page 21

• Manufacturer Part Number: MAX9671CTH+T
• Description: IC AUDIO/VIDEO SWIT DUAL 44TQFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX9671CTH+T

• Function: Audio/Video Switch
• Circuit: 2 x SCART
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 3.3 V ~ 12 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 44-TQFN Exposed Pad
• For Use With: MAX9671EVKIT+ - EVALUATION KIT FOR MAX9671
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The third byte sent to the MAX9670/MAX9671 contains
the data that is written to the chosen register. An
acknowledge pulse from the MAX9670/MAX9671 sig-
nals receipt of the data byte. The address pointer
autoincrements to the next register address after each
received data byte. This autoincrement feature allows a
master to write to sequential register address locations
within one continuous frame. The master signals the
end of transmission by issuing a STOP condition.
The master presets the address pointer by first sending
the MAX9670/MAX9671’s slave address with the R/W
bit set to 0 followed by the register address after a
START condition. The MAX9670/MAX9671 acknowl-
edges receipt of its slave address and the register
address by pulling SDA low during the ninth SCL clock
pulse. A REPEATED START condition is then sent fol-
lowed by the slave address with the R/W bit set to 1.
The MAX9670/MAX9671 transmits the contents of the
specified register. Transmitted data is valid on the ris-
ing edge of the master-generated serial clock (SCL).
The address pointer autoincrements after each read
data byte. This autoincrement feature allows all regis-
ters to be read sequentially within one continuous
frame. A STOP condition can be issued after any num-
ber of read data bytes. If a STOP condition is issued
followed by another read operation, the first data byte
to be read is from the register address location set by
the previous transaction and not 00h and subsequent
reads autoincrement the address pointer until the next
STOP condition. Attempting to read from register
Figure 11. Reading One Indexed Byte of Data from the MAX9670/MAX9671
Figure 12. Reading n Bytes of Indexed Data from the MAX9670/MAX9671
S
S
SLAVE ADDRESS
SLAVE ADDRESS
Volume Control for Dual SCART Connectors
ACKNOWLEDGE FROM
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
ACKNOWLEDGE FROM
MAX9670/MAX9671
______________________________________________________________________________________
R/W
R/W
0
A
0
A
REGISTER ADDRESS
ACKNOWLEDGE FROM
REGISTER ADDRESS
Read Data Format
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
REPEATED START
REPEATED START
A
Sr
A
Sr
SLAVE ADDRESS
addresses higher than 10h results in repeated reads
from a dummy register containing FFh data. The master
acknowledges receipt of each read byte during the
acknowledge clock pulse. The master must acknowl-
edge all correctly received bytes except the last byte.
The final byte must be followed by a not acknowledge
from the master and then a STOP condition. Figures 11
and 12 illustrate the frame format for reading data from
the MAX9670/MAX9671.
When interrupt is enabled in modes 1 and 2, INT, which
is an open-drain output, pulls low under the following
conditions: slow-switch signals change value, CVBS
input signals are detected or disappear, and CVBS out-
put loads are added or removed.
When interrupt is enabled in mode 3, INT pulls low only
when the slow-switch signal changes value.
Enable INT by writing a 1 into bit 4 of register 01h. See
Table 13.
The interrupt can be cleared by reading register 0Eh
and 0Fh.
The maximum full-scale audio signal that can be
applied to the audio inputs is 0.5V
ground. The recommended application circuit to atten-
uate and bias an incoming audio signal is shown in
Figure 13.
ACKNOWLEDGE FROM
SLAVE ADDRESS
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
R/W
R/W
1
Applications Information
A
1
NOT ACKNOWLEDGE FROM MASTER
A
NOT ACKNOWLEDGE FROM MASTER
DATA BYTE
1 BYTE
REGISTER ADDRESS POINTER
AUTOINCREMENT INTERNAL
DATA BYTE
1 BYTE
Interrupt Output
REGISTER ADDRESS POINTER
AUTOINCREMENT INTERNAL
RMS
Audio Inputs
biased at
A
A
P
P
21