MT4C4M4A1TG-5 Micron Technology Inc, MT4C4M4A1TG-5 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT4C4M4A1TG-5
Manufacturer Part Number
MT4C4M4A1TG-5
Description
DRAM Chip FPM 16M-Bit 4Mx4 5V 24-Pin TSOP Tray
Manufacturer
Micron Technology Inc
Type
FPMr
Datasheet
1.MT4C4M4A1TG-5.pdf
(20 pages)
Specifications of MT4C4M4A1TG-5
Package
24TSOP
Density
16 Mb
Address Bus Width
12 Bit
Operating Supply Voltage
5 V
Maximum Random Access Time
50 ns
Operating Temperature
0 to 70 °C
GENERAL DESCRIPTION
state memory containing 16,777,216 bits organized in
a x4 configuration. RAS# is used to latch the row
address (first 11 bits for 2K and first 12 bits for 4K). Once
the page has been opened by RAS#, CAS# is used to latch
the column address (the latter 11 bits for 2K and the
latter 10 bits for 4K; address pins A10 and A11 are “Don’t
Care”).
input. A logic HIGH on WE# dictates read mode, while
a logic LOW on WE# dictates write mode. During a
WRITE cycle, data-in (D) is latched by the falling edge
of WE# or CAS#, whichever occurs last. If WE# goes
LOW prior to CAS# going LOW, the output pins
remain open (High- Z) until the next CAS# cycle,
regardless of OE#.
logic LOW on WE# dictates write mode. During a
WRITE cycle, data-in (D) is latched by the falling edge
of WE# or CAS#, whichever occurs last. An EARLY
WRITE occurs when WE# is taken LOW prior to CAS#
falling. A LATE WRITE or READ-MODIFY-WRITE
occurs when WE# falls after CAS# is taken LOW. During
EARLY WRITE cycles, the data outputs (Q) will remain
High-Z regardless of the state of OE#. During LATE
WRITE or READ-MODIFY-WRITE cycles, OE# must be
taken HIGH to disable the data outputs prior to
applying input data. If a LATE WRITE or READ-
MODIFY-WRITE is attempted while keeping OE# LOW,
no WRITE will occur, and the data outputs will drive
read data from the accessed location.
routed through four pins using common I/O, and pin
direction is controlled by WE# and OE#.
refreshed periodically in order to retain stored data.
FAST PAGE MODE ACCESS
WRITE or READ-MODIFY-WRITE) within a row-
address-defined page boundary. The page cycle is al-
ways initiated with a row address strobed in by RAS#,
followed by a column address strobed in by CAS#.
4 Meg x 4 FPM DRAM
D49_5V.p65 – Rev. 5/00
The 4 Meg x 4 DRAM is a randomly accessed, solid-
READ and WRITE cycles are selected with the WE#
A logic HIGH on WE# dictates read mode, while a
The four data inputs and the four data outputs are
The MT4LC4M4B1 and MT4LC4M4A1 must be
Page operations allow faster data operations (READ,
2
Additional columns may be accessed by providing valid
column addresses, strobing CAS# and holding RAS#
LOW, thus executing faster memory cycles. Returning
RAS# HIGH terminates the page mode of operation,
i.e., closes the page.
DRAM REFRESH
power and executing any RAS# cycle (READ, WRITE)
or RAS# REFRESH cycle (RAS#-ONLY, CBR, or HID-
DEN) so that all combinations of RAS# addresses (2,048
for 2K and 4,096 for 4K) are executed within
(MAX), regardless of sequence. The CBR and SELF
REFRESH cycles will invoke the internal refresh counter
for automatic RAS# addressing.
“S” version. The self refresh feature is initiated by
performing a CBR REFRESH cycle and holding RAS#
LOW for the specified
user the choice of a fully static, low-power data reten-
tion mode or a dynamic refresh mode at the extended
refresh period of 128ms, or 31.25µs per row for a 4K
refresh and 62.5µs per row for a 2K refresh, when using
a distributed CBR REFRESH. This refresh rate can be
applied during normal operation, as well as during a
standby or battery backup mode.
HIGH for a minimum time of
the completion of any internal refresh cycles that may
be in process at the time of the RAS# LOW-to-HIGH
transition. If the DRAM controller uses a distributed
CBR refresh sequence, a burst refresh is not required
upon exiting self refresh. However, if the DRAM con-
troller utilizes RAS#-ONLY or burst CBR refresh se-
quence, all rows must be refreshed with a refresh rate of
t
STANDBY
memory cycle and decreases chip current to a reduced
standby level. The chip is preconditioned for the next
cycle during the RAS# HIGH time.
RC minimum prior to resuming normal operation.
Preserve correct memory cell data by maintaining
An optional self refresh mode is also available the
The self refresh mode is terminated by driving RAS#
Returning RAS# and CAS# HIGH terminates a
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
RASS. The “S” option allows the
t
RPS. This delay allows for
FPM DRAM
4 MEG x 4
©2000, Micron Technology, Inc.
OBSOLETE
t
REF