CY7C037V-20AC Cypress Semiconductor Corp, CY7C037V-20AC Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY7C037V-20AC
Manufacturer Part Number
CY7C037V-20AC
Description
SRAM Chip Async Dual 3.3V 576K-Bit 32K x 18 20ns 100-Pin TQFP
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CY7C037V-20AC.pdf
(18 pages)
Specifications of CY7C037V-20AC
Package
100TQFP
Timing Type
Asynchronous
Density
576 Kb
Typical Operating Supply Voltage
3.3 V
Address Bus Width
15 Bit
Number Of I/o Lines
18 Bit
Number Of Ports
2
Number Of Words
32K
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C037V-20AC
Manufacturer:
CY
Quantity:
61
Document #: 38-06078 Rev. *A
Also, an active busy to a port prevents that port from reading
its own mailbox and, thus, resetting the interrupt to it.
If an application does not require message passing, do not
connect the interrupt pin to the processor’s interrupt request
input pin.
The operation of the interrupts and their interaction with Busy
are summarized in Table 2.
Busy
The CY7C027V/028V and CY7037V/038V provide on-chip ar-
bitration to resolve simultaneous memory location access
(contention). If both ports’ CEs are asserted and an address
match occurs within t
which port has access. If t
permission to the location, but it is not predictable which port will get
that permission. BUSY will be asserted t
or t
Master/Slave
A M/S pin is provided in order to expand the word width by configur-
ing the device as either a master or a slave. The BUSY output of the
master is connected to the BUSY input of the slave. This will allow the
device to interface to a master device with no external components.
Writing to slave devices must be delayed until after the BUSY input
has settled (t
cycle during a contention situation. When tied HIGH, the M/S pin al-
lows the device to be used as a master and, therefore, the BUSY line
is an output. BUSY can then be used to send the arbitration outcome
to a slave.
Semaphore Operation
The CY7C027V/028V and CY7037V/038V provide eight
semaphore latches, which are separate from the dual-port
memory locations. Semaphores are used to reserve resources
that are shared between the two ports.The state of the sema-
phore indicates that a resource is in use. For example, if the
BLC
after CE is taken LOW.
BLC
or t
BLA
PS
), otherwise, the slave chip may begin a write
of each other, the busy logic will determine
PS
is violated, one port will definitely gain
BLA
after an address match
left port wants to request a given resource, it sets a latch by
writing a zero to a semaphore location. The left port then ver-
ifies its success in setting the latch by reading it. After writing
to the semaphore, SEM or OE must be deasserted for t
attempting to read the semaphore. The semaphore value will be
available t
If the left port was successful (reads a zero), it assumes control of the
shared resource, otherwise (reads a one) it assumes the right port
has control and continues to poll the semaphore. When the right side
has relinquished control of the semaphore (by writing a one), the left
side will succeed in gaining control of the semaphore. If the left side
no longer requires the semaphore, a one is written to cancel its re-
quest.
Semaphores are accessed by asserting SEM LOW. The SEM
pin functions as a chip select for the semaphore latches (CE must
remain HIGH during SEM LOW). A
address. OE and R/W are used in the same manner as a normal
memory access. When writing or reading a semaphore, the other
address pins have no effect.
When writing to the semaphore, only I/O
written to the left port of an available semaphore, a one will appear at
the same semaphore address on the right port. That semaphore can
now only be modified by the side showing zero (the left port in this
case). If the left port now relinquishes control by writing a one to the
semaphore, the semaphore will be set to one for both sides. Howev-
er, if the right port had requested the semaphore (written a zero) while
the left port had control, the right port would immediately own the
semaphore as soon as the left port released it. Table 3 shows sam-
ple semaphore operations.
When reading a semaphore, all sixteen/eighteen data lines
output the semaphore value. The read value is latched in an
output register to prevent the semaphore from changing state
during a write from the other port. If both ports attempt to
access the semaphore within t
will definitely be obtained by one side or the other, but there is no
guarantee which side will control the semaphore.
SWRD
+ t
DOE
after the rising edge of the semaphore write.
SPS
CY7C027V/028V
CY7C037V/038V
0–2
of each other, the semaphore
represents the semaphore
0
is used. If a zero is
Page 5 of 18
SOP
before