ADC08831IMX National Semiconductor, ADC08831IMX Datasheet - Page 5

• Manufacturer Part Number: ADC08831IMX
• Description: ADC Single SAR 181KSPS 8-Bit Serial 8-Pin SOIC N T/R
• Manufacturer: National Semiconductor

Specifications of ADC08831IMX

• Package: 8SOIC N
• Resolution: 8 Bit
• Sampling Rate: 181 KSPS
• Architecture: SAR
• Number Of Analog Inputs: 1
• Digital Interface Type: Serial (3-Wire, Microwire)
• Input Type: Voltage
• Signal To Noise Ratio: 48.5(Typ) dB
• Polarity Of Input Voltage: Unipolar

f
SNR
THD
SINAD
ENOB
SFDR
S
The following specifications apply for V
non-coherent 2048 samples with windowing.
Symbol
Dynamic Characteristics
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Note 2: Operating Ratings indicate conditions for which the device is functional. These ratings do not guarantee specific performance limits. For guaranteed speci-
fications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance character-
istics may degrade when the device is not operated under the listed test conditions.
Note 3: All voltages are measured with respect to GND = 0 V
Note 4: When the input voltage V
mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four pins.
Note 5: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
allowable power dissipation at any temperature is P
Note 6: Human body model, 100 pF capacitor discharged through a 1.5 k
Note 7: See AN450 “Surface Mounting Methods and Their Effect on Product Reliability” or Linear Data Book section “Surface Mount” for other methods of soldering
surface mount devices.
Note 8: Typicals are at T
Note 9: Guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 10: Total Unadjusted Error (TUE) includes offset, full-scale, linearity, multiplexer errors.
Note 11: It is not tested for the ADC08832.
Note 12: For V
forward-conduct for analog input voltages one diode drop below ground or one diode drop greater than V
level analog inputs (e.g., 5V) can cause an input diode to conduct, especially at elevated temperatures, which will cause errors for analog inputs near full-scale. The
spec allows 50 mV forward bias of either diode; this means that as long as the analog V
will be correct. Exceeding this range on an unselected channel will corrupt the reading of a selected channel. Achievement of an absolute 0 V
range will therefore require a minimum supply voltage of 4.950 V
Note 13: Channel leakage current is measured after a single-ended channel is selected and the clock is turned off. For off channel leakage current the following two
cases are considered: one, with the selected channel tied high (5 V
measured; two, with the selected channel tied low and the off channels tied high, total current flow through the off channel is again measured. The two cases con-
sidered for determining on channel leakage current are the same except total current flow through the selected channel is measured.
Note 14: A 40% to 60% duty cycle range insures proper operation at all clock frequencies. In the case that an available clock has a duty cycle outside of these limits
the minimum time the clock is high or low must be at least 250 ns. The maximum time the clock can be high or low is 60 µs.
Note 15: Since data, MSB first, is the output of the comparator used in the successive approximation loop, an additional delay is built in to allow for comparator re-
sponse time.
Note 16: For the ADC08832 V
Note 17: Analog inputs are typically 300 ohms input resistance to a 13pF sample and hold capacitor.
Note 18: Effective Number Of Bits (ENOB) is calculated from the measured signal-to-noise plus distortion ratio (SINAD) using the equation ENOB = (SINAD-1.76)/
6.02.
Note 19: The signal-to-noise ratio is the ratio of the signal amplitude to the background noise level. Harmonics of the input signal are not included in it’s calculation.
Note 20: The contributions from the first 6 harmonics are used in the calculation of the THD.
Note 21: The maximum sampling rate is slightly less than f
Sampling Rate
Signal-to -Noise Ratio (Note 19)
Total Harmonic Distortion (Note 20)
Signal-to -Noise and Distortion
Effective Number Of Bits (Note 18)
Spurious Free Dynamic Range
IN(−)
V
IN(+)
J
= 25˚C and represent the most likely parametric norm.
the digital code will be 0000 0000. Two on-chip diodes are tied to each analog input (see Functional Block Diagram) which will
ref
Parameter
is internally tied to V
IN
at any pin exceeds the power supplies (V
ADC08831
ADC08832
CC
D
= 5V, f
= (T
CC
, therefore, for the ADC08832 reference current is included in the supply current.
JMAX
CLK
CLK
DC
/11 if CS is reset in less than one clock period.
− T
DC
, unless otherwise specified.
A
DC
= 2MHz, T
)/
over temperature variations, initial tolerance and loading.
f
f
) and the remaining off channel tied low (0 V
CLK
CLK
JA
or the number given in the Absolute Maximum Ratings, whichever is lower.
/11
/13 (Note 21)
resistor. The machine mode is a 200pF capacitor discharged directly into each pin.
IN
5
<
A
Conditions
= 25˚C, R
(GND) or V
IN
does not exceed the supply voltage by more than 50 mV, the output code
IN
SOURCE
>
V
CC
CC
JMAX
,) the current at that pin should be limited to 5 mA. The 20
supply. During testing at low V
= 50 , f
,
JA
and the ambient temperature, T
DC
(Note 8)
Typical
−59.5
IN
), total current flow through the off channel is
48.5
48.0
62.5
7.7
= 45kHz, V
(Note 9)
Limits
IN
181
153
CC
DC
= 5V
levels (e.g., 4.5V), high
to 5 V
P
A
, V
DC
. The maximum
www.national.com
REF
input voltage
(Limits)
Units
ksps
ksps
Bits
dB
dB
dB
dB
= 5V,