LPC1810FET100,551 NXP Semiconductors, LPC1810FET100,551 Datasheet - Page 42
LPC1810FET100,551
Manufacturer Part Number
LPC1810FET100,551
Description
IC MCU 32BIT 136KB FLSH 100TFBGA
Manufacturer
NXP Semiconductors
Series
LPC18xxr
Datasheets
1.LPC1830FET256551.pdf
(87 pages)
2.LPC1810FET100551.pdf
(2 pages)
3.LPC1810FET100551.pdf
(1164 pages)
Specifications of LPC1810FET100,551
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
150MHz
Connectivity
CAN, EBI/EMI, I²C, Microwire, SPI, SSI, SSP, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
Number Of I /o
64
Program Memory Size
-
Program Memory Type
ROMless
Eeprom Size
-
Ram Size
136K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 12x10b; D/A 1x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TFBGA
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
NXP Semiconductors
LPC1850_30_20_10
Objective data sheet
7.12.8.1 Features
7.12.9.1 Features
7.12.8 LCD controller
7.12.9 Ethernet
The LCD controller provides all of the necessary control signals to interface directly to a
variety of color and monochrome LCD panels. Both STN (single and dual panel) and TFT
panels can be operated. The display resolution is selectable and can be up to 1024 768
pixels. Several color modes are provided, up to a 24-bit true-color non-palettized mode.
An on-chip 512-byte color palette allows reducing bus utilization (i.e. memory size of the
displayed data) while still supporting a large number of colors.
The LCD interface includes its own DMA controller to allow it to operate independently of
the CPU and other system functions. A built-in FIFO acts as a buffer for display data,
providing flexibility for system timing. Hardware cursor support can further reduce the
amount of CPU time needed to operate the display.
Remark: Ethernet is not available on the LPC1820/10 (see
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AHB master interface to access frame buffer.
Setup and control via a separate AHB slave interface.
Dual 16-deep programmable 64-bit wide FIFOs for buffering incoming display data.
Supports single and dual-panel monochrome Super Twisted Nematic (STN) displays
with 4-bit or 8-bit interfaces.
Supports single and dual-panel color STN displays.
Supports Thin Film Transistor (TFT) color displays.
Programmable display resolution including, but not limited to: 320 200, 320 240,
640 200, 640 240, 640 480, 800 600, and 1024 768.
Hardware cursor support for single-panel displays.
15 gray-level monochrome, 3375 color STN, and 32 K color palettized TFT support.
1, 2, or 4 bits-per-pixel (bpp) palettized displays for monochrome STN.
1, 2, 4, or 8 bpp palettized color displays for color STN and TFT.
16 bpp true-color non-palettized for color STN and TFT.
24 bpp true-color non-palettized for color TFT.
Programmable timing for different display panels.
256 entry, 16-bit palette RAM, arranged as a 128 32-bit RAM.
Frame, line, and pixel clock signals.
AC bias signal for STN, data enable signal for TFT panels.
Supports little and big-endian, and Windows CE data formats.
LCD panel clock may be generated from the peripheral clock, or from a clock input
pin.
10/100 Mbit/s
TCP/IP hardware checksum
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 17 February 2011
32-bit ARM Cortex-M3 microcontroller
LPC1850/30/20/10
Table
2).
© NXP B.V. 2011. All rights reserved.
42 of 87