CW1K-3AE11 IDEC, CW1K-3AE11 Datasheet - Page 20

• Manufacturer Part Number: CW1K-3AE11
• Description: 59T4337
• Manufacturer: IDEC

Specifications of CW1K-3AE11

• Contact Configuration: 1NO / 1NC
• Switch Operation: On
• Angle Of Throw: 45°
• Actuator Style: Key
• No. Of Switch Positions: 3
• Contact Current Max: 10A
• Switch Terminals: Screw

USA
IDEC Corporation
Tel: [phone]
[e-mail]
Canada
IDEC Canada Ltd.
Tel: [phone]
[e-mail]
Australia
IDEC Australia Pty. Ltd.
Tel: [phone]
[e-mail]
Pushbuttons
Pushbutton caps cannot be removed. Do not
tamper with the cap using a screwdriver or
pliers, otherwise it may be damaged.
Selector Switches
Turn the selector operator or key to the detent
positions.
Key Selector Switches
To prevent malfunction and damage, take the
following precautions.
• C ompletely insert the key before turning.
• D o not remove the key while turning.
• B esides the standard key (0H), six other keys
• K eys are available in two shapes.
Operating Instructions con’t
are available. Use only a key with a number
that matches the number on the switches’
key cylinder. (The standard key does not have
a key number.)
-0H (standard), 1H, 2H: reversible keys
-3H, 4H, 5H, 6H: non-reversible keys
Make sure of correct insertion direction.
Japan
IDEC Corporation
Tel: [phone]
United Kingdom
IDEC Electronics Ltd.
Tel: [phone]
[e-mail]
[e-mail]
Think Automation and beyond...
Specifications and other descriptions in this catalog are subject to change without notice.
Contact Blocks and LED Modules
To remove the contact block from the operator,
insert a flat screwdriver under the latch and
push the screwdriver down as shown below.
Before removing the LED module, first remove
all contact blocks, and then remove the LED
module in the same manner.
Wiring
Applicable Wires
Stranded wire: 2.0 mm
Solid wire: ø1.6 mm maximum
One or two wires can be connected to the
terminal.
©2011 IDEC Corporation. All Rights Reserved.
Catalog No. CW9Y-B100-1 9/11 7.5K
www.IDEC.com
Germany
IDEC Elektrotechnik GmbH
Tel: [phone]
[e-mail]
Hong Kong
IDEC (H.K.) Co., Ltd.
Tel: [phone]
[e-mail]
2
maximum (14AWG)
8.0 max.
China/Beijing
IDEC (Beijing) Corporation
Tel: [phone]
[e-mail]
China/Shanghai
IDEC (Shanghai) Corporation
Tel: [phone]
[e-mail]
Applicable Crimping Terminals
Spade terminal
When using crimping terminals, be sure to use
insulating tubes or insulated crimping termi-
nals.
Ferrule
When connecting two ferrules to one terminal,
use ferrules without insulation.
When using spade terminals or ferrules,
ensure that they are inserted completely.
Ring terminals cannot be used.
Screw Tightening Torque
Tighten the M3.5 terminal screws to a recom-
mended torque of 1.0 to 1.3 N·m.
Crimping Terminal
8.0 max.
Insulation
0.5 min.
www.IDEC.com/switches
800.262.4332
China/Shenzhen
IDEC (Shenzhen) Corporation
Tel: [phone]
Singapore
IDEC Asia Pte. Ltd.
Tel: [phone]
[e-mail]
Taiwan
IDEC Taiwan Corporation
Tel: [phone]
[e-mail]
11.5 max.
8.1 max.
Insulation Tube
Wire
8.0 max.