SY58024UMI TR Micrel Inc, SY58024UMI TR Datasheet - Page 2

• Manufacturer Part Number: SY58024UMI TR
• Description: IC CROSSPOINT SWITCH DUAL 32MLF
• Manufacturer: Micrel Inc
• Series: SY58r

Specifications of SY58024UMI TR

• Function: Crosspoint Switch
• Circuit: 2 x 2:2
• Current - Supply: 200mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-MLF®, QFN
• Array Configuration: 2x2
• Differential Data Transmission: Yes
• Power Supply Requirement: Single
• Pin Count: 32
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Cascading Capability: No
• Line Code: NRZ
• On-chip Buffers: Yes
• On-chip Decoder: No
• On-chip Latch Circuit: No
• On-chip Mux/demux: No
• Programmable: No
• Operating Supply Voltage (max): 3.6V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Input Level: CML/LVDS/LVPECL
• Output Level: CML
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: SY58024UMITR; SY58024UMITR

Micrel, Inc.
M9999-082807
[e-mail] or [phone]
TRUTH TABLE
PACKAGE/ORDERING INFORMATION
Pin Number
SELB0
SELB1
PIN DESCRIPTION
VTB1
/INB1
VTB0
/INB0
17, 20, 23
INB1
INB0
10,13,16,
SELA0
29, 31,
32, 28,
11, 12,
18, 19,
25, 27
26, 30
15, 14
21, 22
1, 3,
9,24
5, 7
2, 6
8, 4
0
0
1
1
32-Pin MLF
1
2
3
4
5
6
7
8
32 31 30 29 28 27 26 25
9 10 11 12 13 14 15 16
SELA0, SELA1,
SELB1, SELB0
Exposed Pad
VTA0, VTA1,
INA0, /INA0,
INA1, /INA1,
VTB1, VTB0
INB1, /INB1
INB0, /INB0
/QB0, QB0,
/QB1, QB1,
/QA1, QA1,
®
/QA0, QA0
Pin Name
SELA1
(MLF-32)
GND,
VCC
0
1
0
1
24
23
22
21
20
19
18
17
GND
VCC
QA0
/QA0
VCC
QA1
/QA1
VCC
Pin Function
Differential Signal: Each pin of this pair internally terminates with 50Ω to the VT pin. The
input will default to an indeterminate state if left open. See “Input Interface Application”
section.
Input Termination Center-Tap: Each input terminates to this pin. The VT pin provides a
center-tap for each input (IN, /IN) to a termination network for maximum interface flexibility.
See “Input Interface Application” section.
Select Input: TTL/CMOS select input controls that selects inputs IN0, or IN1, for their
respective banks A and B. Each input is internally connected to a 25kΩ pull-up
resistor and will default to a logic high state if left open.
Ground. Exposed pad must be connected to a ground plane that is the same potential as the
device ground pins.
Positive Power Supply: Bypass with 0.1µF0.01µF low ESR capacitors as close to the V
pins as possible.
CML Differential Output Pairs: Differential buffered output copy of the selected input signal.
The CML single-ended output swing is typically 400mV into 50Ω or 100Ω across the pair.
Unused output pairs may be left floating with no impact on jitter. See “CML Output
Termination” section.
INA0
INA0
INA1
INA1
QA0
Ordering Information
Notes:
1. Contact factory for die availability. Dice are guaranteed at T
2. Tape and Reel.
3. Pb-Free package recommended for new designs.
Part Number
SY58024UMI
SY58024UMITR
SY58024UMG
SY58024UMGTR
INA0
INA1
INA0
INA1
QA1
(3)
(2)
(2, 3)
2
Package
MLF-32
MLF-32
SELB0
MLF-32
MLF-32
Type
0
0
1
1
(1)
Operating
Industrial
Industrial
Industrial
Industrial
Range
SELB1
0
1
0
1
Pb-Free bar-line indicator
Pb-Free bar-line indicator
A
SY58024U with
SY58024U with
= 25°C, DC electricals only.
SY58024U
SY58024U
Package
Marking
INB0
INB1
INB1
INB1
QB0
Precision Edge
INB0
INB1
INB0
INB1
SY58024U
QB1
Pb-Free
Pb-Free
NiPdAu
NiPdAu
Finish
Sn-Pb
Sn-Pb
Lead
CC
®