SY58024UMI TR Micrel Inc, SY58024UMI TR Datasheet - Page 4

• Manufacturer Part Number: SY58024UMI TR
• Description: IC CROSSPOINT SWITCH DUAL 32MLF
• Manufacturer: Micrel Inc
• Series: SY58r

Specifications of SY58024UMI TR

• Function: Crosspoint Switch
• Circuit: 2 x 2:2
• Current - Supply: 200mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-MLF®, QFN
• Array Configuration: 2x2
• Differential Data Transmission: Yes
• Power Supply Requirement: Single
• Pin Count: 32
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Cascading Capability: No
• Line Code: NRZ
• On-chip Buffers: Yes
• On-chip Decoder: No
• On-chip Latch Circuit: No
• On-chip Mux/demux: No
• Programmable: No
• Operating Supply Voltage (max): 3.6V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Input Level: CML/LVDS/LVPECL
• Output Level: CML
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: SY58024UMITR; SY58024UMITR

Micrel, Inc.
Absolute Maximum Ratings
Supply Voltage (V
Input Voltage (V
CML Output Voltage (V
Current (V
Input Current (V
Lead Temperature (soldering, 20 sec.) ..................... 260°C
Storage Temperature (T
T
Symbol
V
I
V
V
V
V
R
IN to V
V
Symbol
V
V
I
I
Notes:
1. Permanent device damage may occur if ratings in the “Absolute Maximum Ratings” section are exceeded. This is a stress rating only and functional
2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings.
3. Thermal performance assumes exposed pad is soldered (or equivalent) to the device's most negative potential (GND) on the PCB. θ
4. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established.
5. V
M9999-082807
[e-mail] or [phone]
CC
IH
IL
A
CC
IH
IL
IN
DIFF_IN
IN
CC
IH
IL
DC ELECTRICAL CHARACTERISTICS
LVTTL/CMOS DC ELECTRICAL CHARACTERISTICS
= –40°C to +85°C.
operation is not implied for conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings
conditions for extended periods may affect device reliability.
in still-air, unless otherwise stated.
IH
= 2.5V ±5% or 3.3V ±10%; T
Source or Sink Current on VT pin .................. ±100mA
Source or Sink Current on IN, /IN ..................... ±50mA
(min) not lower than 1.2V.
T
T
)
Parameter
Power Supply Voltage
Power Supply Current
Input HIGH Voltage
Input LOW Voltage
Input Voltage Swing
Differential Input Swing
IN-to-V
Parameter
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
T
IN
)
CC
) ......................................... –0.5V to V
T
) .................................. –0.5V to +4.0V
Resistance
OUT
S
) ........................... –65°C +150°C
) ......... V
A
= -40°C to 85°C
CC
(1)
–1.0V to V
Condition
Condition
2.5V nominal
3.3V nominal
V
50Ω source termination resistor included.
IN, /IN, Note 5
IN, /IN
IN, /IN, see Figure 1a.
IN, /IN, see Figure 1b.
CC
CC
(4)
+0.5V
= max., current through internal
CC
4
Operating Ratings
Supply Voltage (V
Ambient Temperature (T
Package Thermal Resistance
MLF
MLF
Still-Air ............................................................. 35°C/W
500lfpm ............................................................ 28°C/W
Junction-to-board resistance ........................... 20°C/W
(4)
®
®
(θ
(ψ
JA
JB
)
)
CC
) ............................ +2.375V to +3.60V
A
(2)
) ......................... –40°C to +85°C
–300
Min
V
2.0
CC
2.375
Min
(3)
3.0
0.1
0.2
40
0
–1.6
Typ
Typ
200
2.5
3.3
50
Precision Edge
V
Max
2.625
IH
0.8
JA
Max
3.60
1.28
V
40
250
1.7
60
CC
–0.1
uses 4-layer
SY58024U
Units
Units
mA
µA
µA
Ω
V
V
V
V
V
V
V
V
V
®