HI1-0509A-8 Intersil, HI1-0509A-8 Datasheet - Page 20

• Manufacturer Part Number: HI1-0509A-8
• Description: Analog Multiplexer Single 4:1 16-Pin CDIP
• Manufacturer: Intersil
• Type: Analog Multiplexerr

Specifications of HI1-0509A-8

• Package: 16CDIP
• Maximum On Resistance: 1500@±15V Ohm
• Maximum High Level Output Current: 20 mA
• Multiplexer Architecture: 4:1
• Number Of Channels Per Chip: 1
• Maximum Turn-on Time: 500@±15V ns
• Power Supply Type: Dual

Dual-In-Line Plastic Packages (PDIP)
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
SEATING
NOTES:
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,
INDEX
AREA
1. Controlling Dimensions: INCH. In case of conflict between English and
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
4. Dimensions A, A1 and L are measured with the package seated in JE-
5. D, D1, and E1 dimensions do not include mold flash or protrusions.
6. E and
7. e
8. B1 maximum dimensions do not include dambar protrusions. Dambar
9. N is the maximum number of terminal positions.
PLANE
PLANE
BASE
Metric dimensions, the inch dimensions control.
Publication No. 95.
DEC seating plane gauge GS-3.
Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).
ular to datum
e
protrusions shall not exceed 0.010 inch (0.25mm).
E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).
D1
B
B1
C
and e
must be zero or greater.
-A-
e
N
C
1 2 3
A
B
are measured at the lead tips with the leads unconstrained.
are measured with the leads constrained to be perpendic-
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
-C-
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
D
.
0.010 (0.25)
For information regarding Intersil Corporation and its products, see www.intersil.com
e
20
N/2
D1
M
-C-
E1
-B-
C A
A1
HI-506A, HI-507A, HI-508A, HI-509A
A2
B S
L
e
A
C
e
e
C L
E
A
C
B
E16.3
16 LEAD DUAL-IN-LINE PLASTIC PACKAGE
SYMBOL
D1
A1
A2
B1
E1
e
e
A
B
C
D
E
N
e
L
A
B
(JEDEC MS-001-BB ISSUE D)
0.015
0.115
0.014
0.045
0.008
0.735
0.005
0.300
0.240
0.115
MIN
-
-
0.100 BSC
0.300 BSC
INCHES
16
MAX
0.210
0.195
0.022
0.070
0.014
0.775
0.325
0.280
0.430
0.150
-
-
18.66
MILLIMETERS
0.39
2.93
0.356
1.15
0.204
0.13
7.62
6.10
2.93
MIN
-
-
2.54 BSC
7.62 BSC
16
19.68
10.92
MAX
5.33
4.95
0.558
1.77
0.355
8.25
7.11
3.81
-
-
October 30, 2007
Rev. 0 12/93
NOTES
8, 10
FN3143.6
4
4
5
5
6
5
6
7
4
9
-
-
-
-