SI3220-FQ Silicon Laboratories Inc, SI3220-FQ Datasheet - Page 37

• Manufacturer Part Number: SI3220-FQ
• Description: IC SLIC/CODEC DUAL-CH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: ProSLIC®r

Specifications of SI3220-FQ

• Function: Subscriber Line Interface Concept (SLIC), CODEC
• Interface: GCI, PCM, SPI
• Number Of Circuits: 2
• Voltage - Supply: 3.3V, 5V
• Current - Supply: 65mA
• Power (watts): 941mW
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: *
• Includes: Battery Switching, BORSCHT Functions, DTMF Generation and Decoding, FSK Tone Generation, Modem and Fax Tone Detection
• Product: Telecom
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Transistor Power Equations
(Using Discrete Transistors)
When using the Si3220 or Si3225 along with discrete
bipolar transistors, it is possible to control the total
power of the solution by individually regulating the
power in each discrete transistor. Figure 18 illustrates
the basic transistor-based linefeed circuit for one
channel. The power dissipation of each external
transistor is estimated based on the A/D sample values.
The approximate power equations for each external
BJT are as follows:
P
P
P
P
P
P
The maximum power threshold for each device is
software-programmable and should be set based on the
characteristics of the transistor package, PCB design,
and available airflow. If the peak power exceeds the
programmed threshold for any device, the power-alarm
bit is set for that device. Each external bipolar has its
own register bit (PQ1S–PQ6S bits of the IRQVEC3
register), which goes high on a rising edge of the
comparator output and remains high until the user
clears it. Each transistor power alarm bit is also
maskable by setting the PQ1E–PQ6E bits in the
IRQEN3 register.
Si3200 Power Calculation
When using the Si3200, it is also possible to detect the
thermal conditions of the linefeed circuit by calculating
the total power dissipated within the Si3200. This case
is similar to the transistor power equations case, with
the exception that the total power from all transistor
devices is dissipated within the same package
enclosure, and the total power result is placed in the
PSUM RAM location. The power calculation is derived
using the following set of equations:
P
P
P
P
P
P
PSUM = total dissipated power = P
P
Note: The Si3200 THERM pin must be connected to the
Q1
Q2
Q3
Q4
Q5
Q6
Q1
Q2
Q3
Q4
Q5
Q6
Q4
≅ V
≅ V
≅ V
≅ V
≅ V
≅ V
≅ (|V
≅ (|V
≅ (|V
≅ (|V
≅ (|V
≅ (|V
+ P
THERM a/b pin of the Si3220/Si3225 in order for the
Si3200 power calculation method to work correctly.
CE1
CE2
CE3
CE4
CE5
CE6
Q5
TIP
RING
BAT
BAT
BAT
BAT
+ P
x I
x I
x I
x I
x I
x I
| + 0.75 V) x I
| + 0.75 V) x I
| – |V
| – |V
|+ 0.75 V) x I
| + 0.75 V) x I
Q1
Q2
Q3
Q4
Q5
Q6
Q6
≅ (|V
≅ (|V
≅ (|V
≅ (|V
≅ (|V
≅ (|V
RING
TIP
|) x I
TIP
RING
BAT
BAT
BAT
BAT
|) x I
| + 0.75 V) x (I
Q6
| – R7 x I
| – R6 x I
| – |V
| – |V
Q1
Q3
Q4
| + 0.75 V) x (I
Q5
Q2
RING
TIP
| – R6 x I
Q5
Q6
| – R7 x I
Q1
) x (I
) x (I
Q1
+ P
Q2
Q3
Q4
)
Q6
)
Q2
)
)
Q5
) x (I
) x (I
+ P
Q6
Q3
Q5
)
Rev. 1.0
)
+
Power Filter and Alarms
The power calculated during each A/D sample period
must be filtered before being compared to a user-
programmable maximum power threshold. A simple
digital low-pass filter is used to approximate the
transient thermal behavior of the package, with the
output of the filter representing the effective peak power
within the package or, equivalently, the peak junction
temperature.
For Q1, Q2, Q3, and Q4 in SOT23 and Q5 and Q6 in
SOT223 packages, the settings for thermal low-pass
filter poles and power threshold settings are (for an
ambient temperature of 70 °C) calculated as follows: If
the thermal time constant of the package is τ
decimal values of RAM locations PLPF12, PLPF34, and
PLPF56 are given by rounding to the next integer the
value given by the following equation:
Where 4096 is the maximum value of the 12-bit plus
sign RAM locations PLPF12, PLPF34, and PLPF56,
and 800 is the power calculation clock rate in Hz. The
equation is an excellent approximation of the exact
equation for τ
above equations in mind, example values of the RAM
locations, PTH12, PTH34, PTH56, PLPF12, PLPF34,
and PLPF56 are as follows:
PTH12 = power threshold for Q1, Q2 = 0.3 W (0x25A)
PTH34 = power
(0x1B5E)
PTH56 = power threshold for Q5, Q6 = 1 W (0x7D8)
PLPF12 = Q1/Q2 thermal LPF pole = 0x0012
(for SOT–89 package)
PLPF34 = Q3/Q4 thermal LPF pole = 0x008C
(for SOT–23 package)
PLPF56 = Q5/Q6 thermal LPF pole = 0x000E
(for SOT–223 package)
In the case where the Si3200 is used, thermal filtering
needs to be performed only on the total power reflected
in the PSUM RAM location. When the filter output
exceeds the total power threshold, an interrupt is
issued. The PTH12 RAM location is used to preset the
total power threshold for the Si3200, and the PLPF12
RAM location is used to preset the thermal low-pass
filter pole.
PLPFxx (decimal value)
thermal
threshold
= 1.25 ms … 5.12 s. With the
Si3220/Si3225
=
for
------------------------------------
800
4096
×
Q3,
τ
thermal
Q4 = 0.22 W
×
thermal
2
3
, the
37