SC16IS750IBS,151 NXP Semiconductors, SC16IS750IBS,151 Datasheet - Page 24

• Manufacturer Part Number: SC16IS750IBS,151
• Description: IC UART I2C/SPI 24-HVQFN
• Manufacturer: NXP Semiconductors
• Type: IrDA or RS- 232 or RS- 485r

Specifications of SC16IS750IBS,151

• Number Of Channels: 1, UART
• Package / Case: 24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
• Features: Low Current
• Fifo's: 64 Byte
• Protocol: RS232, RS485
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 5 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.3 V
• Supply Current: 6 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 2.5 V or 3.3 V
• Transmit Fifo: 64Byte
• Receive Fifo: 64Byte
• Transmitter And Receiver Fifo Counter: No
• Operating Supply Voltage (max): 3.6V
• Mounting: Surface Mount
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-2234; 935279271151; SC16IS750IBS-S

NXP Semiconductors
SC16IS740_750_760_6
Product data sheet
8.4 Line Control Register (LCR)
[1]
This register controls the data communication format. The word length, number of stop
bits, and parity type are selected by writing the appropriate bits to the LCR.
shows the Line Control Register bit settings.
Table 12.
Bit
7
6
5
4
3
2
1:0
FIFO reset requires at least two XTAL1 clocks, therefore, they cannot be reset without the presence of the
XTAL1 clock.
Symbol
LCR[7]
LCR[6]
LCR[5]
LCR[4]
LCR[3]
LCR[2]
LCR[1:0]
Line Control Register bits description
Single UART with I
Description
divisor latch enable
Break control bit. When enabled, the break control bit causes a break
condition to be transmitted (the TX output is forced to a logic 0 state).
This condition exists until disabled by setting LCR[6] to a logic 0.
Set parity. LCR[5] selects the forced parity format (if LCR[3] = 1).
parity type select
parity enable
Number of stop bits. Specifies the number of stop bits.
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received; see
Rev. 06 — 13 May 2008
logic 0 = divisor latch disabled (normal default condition)
logic 1 = divisor latch enabled
logic 0 = no TX break condition (normal default condition).
logic 1 = forces the transmitter output (TX) to a logic 0 to alert the
communication terminal to a line break condition
logic 0 = parity is not forced (normal default condition).
LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a logical 1
for the transmit and receive data.
LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a logical 0
for the transmit and receive data.
logic 0 = odd parity is generated (if LCR[3] = 1)
logic 1 = even parity is generated (if LCR[3] = 1)
logic 0 = no parity (normal default condition).
logic 1 = a parity bit is generated during transmission and the receiver
checks for received parity
0 to 1 stop bit (word length = 5, 6, 7, 8)
1 to 1.5 stop bits (word length = 5)
1 = 2 stop bits (word length = 6, 7, 8)
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
SC16IS740/750/760
Table
15.
© NXP B.V. 2008. All rights reserved.
Table 12
24 of 62