SC16C654DBIB64,157 NXP Semiconductors, SC16C654DBIB64,157 Datasheet - Page 29
![IC QUAD UART 64BYTE 64LQFP](/photos/6/98/69856/568-64-lqfp_sot314-2_sml.jpg)
SC16C654DBIB64,157
Manufacturer Part Number
SC16C654DBIB64,157
Description
IC QUAD UART 64BYTE 64LQFP
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C654BIBS528.pdf
(58 pages)
Specifications of SC16C654DBIB64,157
Number Of Channels
4, QUART
Fifo's
64 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
64-LQFP
Transmit Fifo
64Byte
Receive Fifo
64Byte
Transmitter And Receiver Fifo Counter
Yes
Data Rate
5Mbps
Package Type
LQFP
Operating Supply Voltage (max)
5.5V
Mounting
Surface Mount
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935276671157
SC16C654DBIB64
SC16C654DBIB64
SC16C654DBIB64
SC16C654DBIB64
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C654DBIB64,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
9397 750 14965
Product data sheet
7.4 Interrupt Status Register (ISR)
The SC16C654B/654DB provides six levels of prioritized interrupts to minimize external
software interaction. The Interrupt Status Register (ISR) provides the user with six
interrupt status bits. Performing a read cycle on the ISR will provide the user with the
highest pending interrupt level to be serviced. No other interrupts are acknowledged until
the pending interrupt is serviced. Whenever the interrupt status register is read, the
interrupt status is cleared. However, it should be noted that only the current pending
interrupt is cleared by the read. A lower level interrupt may be seen after re-reading the
interrupt status bits.
prioritized interrupt levels and the interrupt sources associated with each of these interrupt
levels.
Table 13:
Table 14:
Priority
level
1
2
2
3
4
5
6
Bit
7:6
5:4
3:1
0
Interrupt source
Interrupt Status Register bits description
ISR[5]
0
0
0
0
0
0
1
Symbol
ISR[7:6]
ISR[5:4]
ISR[3:1]
ISR[0]
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
ISR[4]
0
0
0
0
0
1
0
Table 13 “Interrupt source”
Rev. 02 — 20 June 2005
Description
FIFOs enabled. These bits are set to a logic 0 when the FIFO is not
being used. They are set to a logic 1 when the FIFOs are enabled.
INT priority bits 4:3. These bits are enabled when EFR[4] is set to a
logic 1. ISR[4] indicates that matching Xoff character(s) have been
detected. ISR[5] indicates that CTS, RTS have been generated. Note
that once set to a logic 1, the ISR[4] bit will stay a logic 1 until Xon
character(s) are received.
INT priority bits 2:0. These bits indicate the source for a pending
interrupt at interrupt priority levels 1, 2, and 3; see
INT status.
logic 0 or cleared = default condition
logic 0 or cleared = default condition
Logic 0 or cleared = default condition.
logic 0 = an interrupt is pending and the ISR contents may be used as
a pointer to the appropriate interrupt service routine
logic 1 = no interrupt pending (normal default condition)
ISR[3]
0
0
1
0
0
0
0
ISR[2]
1
1
1
0
0
0
0
ISR[1]
1
0
0
1
0
0
0
shows the data values (bits 0:5) for the six
SC16C654B/654DB
ISR[0]
0
0
0
0
0
0
0
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Source of the interrupt
LSR (Receiver Line Status
Register)
RXRDY (Receive Data
Ready)
RXRDY (Receive Data
time-out)
TXRDY (Transmitter Holding
Register Empty)
MSR (Modem Status
Register)
RXRDY (Received Xoff
signal)/Special character
CTS, RTS change of state
Table
13.
29 of 58