PS21869 MITSUBISHI, PS21869 Datasheet
![no-image](/images/manufacturer_photos/0/4/451/mitsubishi_sml.jpg)
PS21869
Available stocks
Related parts for PS21869
PS21869 Summary of contents
Page 1
... A B HEAT SINK SIDE D DETAIL C (2 parts) PS21869-P/AP INTEGRATED POWER FUNCTIONS 600V/50A CSTBT inverter bridge for three phase DC-to-AC power conversion Refer Fig. 6 for long-pin type : PS21869-AP. C (2. (0. MIN (2) 2.5 3.8 (1.5) 1 0.2 ...
Page 2
... When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive recommended to stop the system when the Fo signal is received and check the fault Collector current waveform 0 2 PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE C2 (Note 7) C1 (Note 6) Protection circuit (UV) DIP-IPM H-side IGBT S U ...
Page 3
... Sinusoidal minute, connection pins to heat-sink plate Control Terminals Groove DIP-IPM 18mm AI board 13.5mm IGBT Chip Temp. measurement point (inside the AI board) FWDi Chip PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE Ratings 450 500 600 50 100 70.4 (Note 1) –20~+125 100 C) however, to en- f 125 100 C). ...
Page 4
... Trip level Reset level T 125 C j Trip level Reset level C = 22nF FO Applied between according to the following approximate equation : C FO PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — — 1.42 — — 2.00 Limits Min. Typ. Max. — 2. 1.50 — 2.10 1 ...
Page 5
... C T 100 C, f N-line wiring inductance less Between 1.7 times and than 10nH (Note 9) 2.0 times of rated current between V -N (including surge) NC PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — 0.98 1.47 — 65 — ( Note 6 ) – ...
Page 6
... Broken line ... off pulse width < PWIN(off) : turn on time t2 HVIC1 IGBT1 Di1 COM S HVIC2 V V IGBT2 Di2 COM S HVIC3 V V IGBT3 Di3 COM S IGBT4 LVIC Di4 U OUT V CC IGBT5 Di5 V OUT U N IGBT6 Di6 OUT CIN GND CFO CFO CIN PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM Jul. 2005 ...
Page 7
... Fig. 6 PACKAGE OUTLINES (Long-pin type : PS21869-AP) (1) (3.1) (4.5) remains (1) (1.5) (1.5) (10) (1.5) (11) remains 21.4 13.4 0.5 0.5 35 0.6 31 0.5 (1) 11.5 0.5 (10) (2.9) (3.5) (4.65) (4.65) (3.5) PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE 1.6 0.5 0.5MAX solder Irregular 1.6 0.5 0.5MAX solder Irregular 16 0 ...
Page 8
... Protection circuit state Control supply voltage V Output current Ic Error output Fo signal is set by the external capacitor SET RESET reference voltage CR circuit time constant DELAY the circuits start to operate when next input is applied. Dr RESET SET PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE . FO RESET b6 b7 Jul. 2005 ...
Page 9
... (Logic) NC Wiring inductance should be less than 10nH. Equivalent to the inductance of a copper pattern with length=17mm, width=3mm, and thickness=100 m N Shunt resistor Please make the GND wiring connection of shunt resistor to the V as possible. PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE RESET terminal as close NC Jul. 2005 ...
Page 10
... GND CFO CIN CFO C4 Long GND wiring here might generate If this wiring is too long, the SC level noise to input and cause IGBT fluctuation might be larger and cause malfunction. SC malfunction. PS21869-P/AP TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM Too long wiring here might cause short-circuit ...