2206CP Exar Corporation, 2206CP Datasheet
2206CP
Related parts for 2206CP
2206CP Summary of contents
Page 1
... The output waveforms can be both amplitude and frequency modulated by an external voltage. Frequency of operation can be selected externally over a range of 0.01Hz to more than 1MHz. ORDERING INFORMATION Part No. XR-2206M XR-2206P XR-2206CP XR-2206D Rev. 1.03 1972 EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 TM APPLICATIONS Waveform Generation ...
Page 2
XR-2206 5 TC1 Timing Capacitor 6 TC2 7 TR1 Timing Resistors 8 TR2 9 FSKI AMSI 1 WAVEA1 13 WAVEA2 14 SYMA1 15 SYMA2 16 Rev. 1.03 V GND BIAS VCO Current Multiplier Switches And Sine ...
Page 3
AMSI 1 STO TC1 5 TC2 6 TR1 7 TR2 8 16 Lead PDIP, CDIP (0.300”) PIN DESCRIPTION Pin # Symbol Type Description 1 AMSI I Amplitude Modulating Signal Input. 2 STO O Sine ...
Page 4
... Notes 1 Output amplitude is directly proportional to the resistance For maximum amplitude stability, R should be a positive temperature coefficient resistor. 3 Bold face parameters are covered by production test and guaranteed over operating temperature range. Rev XR-2206M/P XR-2206CP/D Typ. Max. Min. Typ. Max +13 +5 +13 12 ...
Page 5
... The VCO produces an output frequency proportional to an input current, which is set by a resistor from the timing Rev. 1.03 (CONT’D) XR-2206CP/D Typ. Max. Min. Typ. Max. 100 ...
Page 6
XR-2206 FSK Input Î Î Î Î Î Î Î Î Î Î Triangle Î Î Î Î Î Î Î Î Î Î 5 Î Î Î Î Î ...
Page 7
MAXIMUM TIMING R 1M NORMAL RANGE 100K TYPICAL VALUE 10K MINIMUM TIMING Frequency (Hz) Figure 5. R versus Oscillation Frequency. Î Î Î Î Î Î Î Î Î Î Î Î ...
Page 8
XR-2206 3 C=0. R=1M R=2K 1 R=10K R=200K R=200K 0 R=10K R=2K R=1M -1 R=1K -2 R=1K -3 -50 - Ambient Temperature (C ) Figure 9. Frequency Drift versus Temperature ...
Page 9
Figure 12. Circuit for Sine Wave Generation with Minimum Harmonic Distortion. (R Determines Output Swing - See Figure >2V 1 ...
Page 10
XR-2206 Figure 14. Circuit for Pulse and Ramp Generation. Frequency-Shift Keying The XR-2206 can be operated with two separate timing resistors, R and R , connected to the timing Pin 7 and respectively, as shown in Figure ...
Page 11
With External Adjustment: The harmonic content of sinusoidal output can be reduced to -0.5% by additional adjustments as shown in Figure 12. The potentiometer, sine-shaping resistor, and R provides the fine B adjustment for the waveform symmetry. The adjustment procedure ...
Page 12
XR-2206 Output Amplitude: Maximum output amplitude is inversely proportional to the external resistor connected to Pin 3 (see 3 Figure 3 ). For sine wave output, approximately 60mV peak per peak amplitude is approximately 160mV ...
Page 13
LEAD CERAMIC DUAL-IN-LINE Base 1 Plane Seating L Plane B SYMBOL Note: The control dimension is the inch column Rev. 1.03 (300 MIL ...
Page 14
XR-2206 16 LEAD PLASTIC DUAL-IN-LINE Seating Plane L B SYMBOL Note: The control dimension is the inch column ...
Page 15
LEAD SMALL OUTLINE (300 MIL JEDEC SOIC Seating Plane e SYMBOL Note: The control dimension is the millimeter column Rev. 1.03 Rev. 1. ...
Page 16
... While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized ...