M52348SP Mitsumi Electronics, Corp., M52348SP Datasheet
M52348SP
Available stocks
Related parts for M52348SP
M52348SP Summary of contents
Page 1
... DESCRIPTION The M52348SP is an semiconductor IC for RGBHV interface that switches signals input from two types of image source and outputs them to CRT display etc. The synchronous signal meets the frequency band of 10 kHz to 200 kHz and is output with TTL. The IC adopts 250 MHz for the frequency band width of video signal, providing high resolution images ...
Page 2
... SG4 SG4 SG4 Takes ratio of the values above abb bab bba SG5 SG5 SG5 - - - - - abb bab bba - - - - - SG5 SG5 SG5 MITSUBISHI ICs (Monitor) M52348SP Unit V mW ˚C ˚ Limits Unit SW15 SW16 SW17 Min. Typ. Max. Hin2 Vin2 Swich GND ...
Page 3
... SG7 SG7 SG7 - - - SG7 SG1 SG1 SG1 SG7 SG7 - - - SG1 SG1 SG1 SG7 MITSUBISHI ICs (Monitor) M52348SP SW Limits Unit SW16 SW17 Min. Typ. Max. Vin2 Swich GND -60 - OPEN OPEN -60 - GND GND -40 - OPEN OPEN -40 - GND -50 - GND -50 - OPEN -30 -25 ...
Page 4
... Assign SW17 to OPEN and then input SG3 into pin Measure the output amplitude of T.P.31 at that time and specify the value Assign SW17 to GND and then measure the output amplitude of T.P.31 at that time. Specify the value MITSUBISHI ICs (Monitor) M52348SP , and G , find G and G ...
Page 5
... Table. Assign SW17 to GND (or OPEN), input SG7 into the input pin and measure the output waveform. Rising delay time Trd1 (Trd2) and falling delay time Tfd1 (Tfd2) shall be found according to the following diagram. SG7 OOO MITSUBISHI ICs (Monitor) M52348SP 100% 90% 10 ...
Page 6
... TTL, f=60 kHz, duty = 50%) O-P SG7 WIDE FREQUENCY BAND ANALOG SWITCH TYPICAL CHARACTERISTICS THERMAL DERATING (MAXIMUM RATING) 2000 , and . Input 1603 1600 1200 800 , and and 400 -20 0 AMBIENT TEMPERATURE Ta (˚C) P-P ) P-P ) P-P ) P MITSUBISHI ICs (Monitor) M52348SP 100 125 150 6 ...
Page 7
... TEST CIRCUIT 0.01 7 MITSUBISHI ICs (Monitor) M52348SP WIDE FREQUENCY BAND ANALOG SWITCH TP6 0.01 TP4 0.01 0.01 TP2 0.01 Units Reslstance : Capacitance : F ...
Page 8
... CC1 5 INPUT1(R) 2 INPUT1(G) 4 INPUT1(B) 6 1.0mA INPUT1(H) 7 INPUT1( GND INPUT2(R) 10 INPUT2(G) 12 INPUT2(B) 14 1.0mA MITSUBISHI ICs (Monitor) WIDE FREQUENCY BAND ANALOG SWITCH DC voltage (V) 5.0 Input at low impedance. 2.0 Input pulse more and 5V or less. - 0.2mA GND Input at low impedance. 2.0 M52348SP Description of function ...
Page 9
... WIDE FREQUENCY BAND ANALOG SWITCH DC voltage (V) - 0.2mA 7.3k 2.6 2.3V - 5.0 - 1.5 2 500 , , 5.0 MITSUBISHI ICs (Monitor) M52348SP Description of function Input pulse more and 5V or less Enables switching between OPEN and GND. Contains output resistance. Apply the same voltage. Contains output resistance. ...
Page 10
... Vcc shall use a stable power supply. (Individual Vcc should use an independent power supply.) or • Insertion of a resistance of several tens of pin and the circuit at the next stage makes oscillation harder. • GND should be as wide as possible. Basically, solid earth should be used. ) are as shown more. MITSUBISHI ICs (Monitor) M52348SP between the output 10 ...