TDA5241 NXP Semiconductors, TDA5241 Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TDA5241
Available stocks
Related parts for TDA5241
TDA5241 Summary of contents
Page 1
Product specification File under Integrated Philips Semiconductors ~[}{]~~¥ Circuits, ICO1 November 96 re ...
Page 2
... VCR scanner GENERAL DESCRIPTION The TDA5241 is a bipolar integrated circuit used to drive brush less DC motors in full-wave mode. The device senses the rotor position using an EMF-sensing technique and is ideally suited as a drive circuit for VCR scanner motors. QUICK REFERENCE ...
Page 3
... Philips Semiconductors Brushless DC motor drive circuit ORDERING INFORMATION . . March 1997 Fig.1 Power derating curve . 3/19 Product specification TDA5241 ...
Page 4
... Philips Semiconductors 8 Brushless DC motor drive circuit BLOCK DIAGRAM March 1997 4/19 Product specification TDA5241 ...
Page 5
... I not connected I driver output TDA5241 Fig.3 Pin configuration. 5/19 Product TDA5241 DESCRIPTION 18 MOT1 17 n.c MOT3 16 15 CAP-CPC 14 MOTO CTLIN 13 12 CAP- TI CAP-ST 111 CAP-CDS ...
Page 6
... Brushless DC motor drive circuit FUNCTIONAL DESCRIPTION The TDA5241 offers a sensorless three phase motor drive function unique in its combination of sensorless motor drive and full-wave drive. The TDA5241 offers protected outputs capable of handling high currents and can be used with star or delta connected motors ...
Page 7
... O note 5 – 0 See Fig. 6 0 CAPCPC CAP–CPC = 100 nF 4 1.5V and CTLIN CTLIN –0.3 – – 7/19 Product specification TDA5241 Typ Max Unit – 5 140 150 C T –30 – – – – ...
Page 8
... PG IN pulse 5 7 1.5 2.0 –2.5 –2.0 – 0.20 – 0.30 – 2. –70 –63 –6.0 –5.3 – 50 – 0.30 – 2.20 10.6 16.2 –5.3 –8.1 1.85 2.05 780 860 2.3 2.4 8/19 Product specification TDA5241 Max Unit 0 – 0 – – – – 2.5 mA –1.5 – V – V – – ...
Page 9
... Switching levels with respect to MOT1, MOT2 and MOT3. 4. Drivers are in high impedance OFF–state. 5. The outputs are short–circuit protected by limiting the current and the IC temperature. March 1997 Conditions Min 10.1 –20.9 0.9 780 2.3 1 –100 = Fig. 4 Switching levels 9/19 Product specification TDA5241 Typ Max Unit 15.5 20.9 A –15.5 –10.1 A 1.025 1.15 860 940 mV 2.4 2.55 V – ...
Page 10
... A PG output signal is generated; pulse width is typically 7 ~s. Table 1 OUTPUT STATES MOT1 STATE Table1 , the sequence of the six possible 8 March 1997 MOT3 MOT2 states of the outputs has been depicted 10/19 Product specification TDA5241 ...
Page 11
... Philips Semiconductors Brushless DC motor drive circuit . . March 1997 Fig.5 Typical application of the TDA5241. 11/19 Product specification TDA5241 ...
Page 12
... EMF the TDA5241 will run the motor. If the amount of EMF generated is insufficient, then the motor will move one step only and will oscillate in its new position. ...
Page 13
... C) ms (witch C in nF) 6231 CAP-CDM = 400= 15.6 (choose 18 nF) and CAP-DC typical voltage waveforms (ZCR = Zero-crossing ; COM = COMMUTATION) 13/19 Product TDA5241 220 nF). in nF) is generated by the discharge -Vmax=Vih -Vil in normal running mode. specification is high from ...
Page 14
... Fig.8 Typical CAP- TI and VMOT1 voltage waveforms in normal running mode. 8 March 1997 = 2. ms 2.63 x 3.5 = 9.2 (choose 10 nF) can occur in certain positions of a blocked direction (synchronously with little torque). 14/19 Product specification TDA5241 rotor. If the chosen value is too large, then it is ...
Page 15
... FG SIGNAL The FG signal is generated in the TDA5241 by using the zero-crossing of the motor EMF from the three motor windings. Every zero-crossing in a (star connected) motor winding is used to toggle the FG output signal. The FG frequency is therefore half the commutation frequency. All transitions indicate the detection of a zero-crossing (except for PG). The negative-going edges are called FG pulses because they generate an interrupt in a controlling microprocessor ...
Page 16
... This means that the current to and from the output stages is limited. .Thermal protection of the six output transistors is achieved by each transistor having a thermal sensor that is active when the transistor is switched on. The transistors are switched off when the local temperature becomes too high. March 1997 16/19 Product specification TDA5241 ...
Page 17
... Philips Semiconductors Brushless DC motor drive circuit PACKAGE OUTLINE 8 Dimensions in mm Fig.10 March 1997 PLASTIC DUAL IN-LINE PACKAGE; 17/19 Product TDA5241 MSA259 18 LEADS; SOT102RG4 specification ...
Page 18
... V) applied to the flat part of the lead. Contact time must be limited to' 10 seconds 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 °C. March 1997 18/19 Product specification TDA5241 ...
Page 19
... Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. hilips Semiconductors yyyy mmm dd Fax: + 24825 Document order number: 1 Product specification TDA5241 Koninklijke Philips Electronics N.V. 1996 All rights reserved. Printed in U.S.A. Date of release: 11-96 9397 750 08755 ...