M51995FP Mitsumi Electronics, Corp., M51995FP Datasheet
![no-image](/images/manufacturer_photos/0/4/452/mitsumi_electronics__corp__sml.jpg)
M51995FP
Available stocks
Related parts for M51995FP
M51995FP Summary of contents
Page 1
DESCRIPTION M51995A is the primary switching regulator controller which is especially designed to get the regulated DC voltage from AC power supply. This IC can directly drive the MOS-FET with fast rise and fast fall output pulse. Type M51995A has ...
Page 2
BLOCK DIAGRAM V CC UNDER ON/OFF VOLTAGE LOCKOUT OVP(shut down) LATCH OSCILLATOR CAPACITANCE CF OSCILLATOR OSCILLATOR RESISTANCE T-ON (ON duty) (TRIANGLE) OSCILLATOR RESISTANCE T-OFF (OFF duty) VF ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Supply voltage CC V Collector voltage C ...
Page 3
ELECTRICAL CHARACTERISTICS Symbol Parameter Block Operating supply voltage range Operation start up voltage CC(START) V Operation stop voltage CC(STOP) Difference voltage between Vcc operation start and stop Stand-by current Icc L Icc Operating circuit current O Circuit ...
Page 4
ELECTRICAL CHARACTERISTICS Symbol Parameter Block Oscillating frequency f OSC T Maximum ON duty DUTY Upper limit voltage of oscillation waveform V OSCH V Lower limit voltage of oscillation waveform OSCL Voltage difference between upper limit and V OSC lower limit ...
Page 5
TYPICAL CHARACTERISTICS THERMAL DERATING (MAXIMUM RATING) 1800 1500 1200 900 600 300 100 AMBIENT TEMPERATURE Ta(°C) CIRCUIT CURRENT VS.SUPPLY VOLTAGE (OVP OPERATION) 8.0 OVP RESET POINT 8.87V(-30°C) 7.0 8.94V(25°C) 9.23V(85°C) 6.0 5.0 Ta=-30°C 4.0 ...
Page 6
THRESHOLD VOLTAGE OF ON/OFF TERMINAL VS.AMBIENT TEMPERATURE 3.4 3.2 3.0 ON OFF 2.8 2.6 2.4 OFF ON 2.2 2.0 1.8 -40 - AMBIENT TEMPERATURE Ta(°C) INPUT CURRENT OF VF TERMINAL VS.INPUT VOLTAGE - ...
Page 7
VF THRESHOLD VOLTAGE FOR TIMER VS. AMBIENT TEMPERATURE 3.5 3.0 2.5 -40 - -60 AMBIENT TEMPERATURE Ta(°C) THRESHOLD VOLTAGE OF CLM- TERMINAL VS. AMBIENT TEMPERATURE 205 200 195 -40 - -60 AMBIENT ...
Page 8
OUTPUT LOW VOLTAGE VS. OUTPUT SINK CURRENT 5.0 Ta=25°C 4.0 3.0 Vcc=18V 2.0 Vcc=5V 1.0 0 10m 100m 1 1m OUTPUT SINK CURRENT I (A) OL INPUT CURRENT OF DETECTION AMP VS. AMBIENT TEMPERATURE 1.6 1.5 1.4 1.3 1.2 1.1 ...
Page 9
ON duty VS. F/B TERMINAL INPUT CURRENT 50 (f =500kHz) OSC R =18k ON R =20k OFF 40 30 Ta=-30°C Ta=25°C Ta=85° 0.5 1.0 1.5 F/B TERMINAL INPUT CURRENT I OSCILLATING FREQUENCY VS. CF TERMINAL CAPACITY ...
Page 10
ON duty VS. AMBIENT TEMPERATURE 100 (f =100kHz) OSC -60 -40 - AMBIENT TEMPERATURE Ta(°C) ON duty VS. AMBIENT TEMPERATURE 100 (f =500kHz) OSC 90 80 ...
Page 11
CURRENT FROM OVP TERMINAL FOR OVP RESET VS. SUPPLY VOLTAGE 800 700 600 500 Ta=-30°C Ta=25°C 400 Ta=85°C 300 200 100 SUPPLY VOLTAGE Vcc(V) MITSUBISHI (Dig./Ana. INTERFACE) SWITCHING REGULATOR CONTROL 35 40 ...
Page 12
FUNCTION DESCRIPTION Type M51995AP and M51995AFP are especially designed for off-line primary PWM control IC of switching mode power supply (SMPS) to get DC voltage from AC power supply. Using this IC,smart SMPS can be realized with reasonable cost and ...
Page 13
Start-up circuit section The start-up current is such low current level as typical 90µ A,as shown in Fig.3,when the Vcc voltage is increased from low level to start-up voltage Vcc (START) In this voltage range,only a few parts in this ...
Page 14
OSC control circuit operates. When over current signal is applied to CLM+ or CLM- terminal,and the current limiting circuit,intermittent action and OSC control circuit starts to operate.In this case T-OFF terminal voltage depends on ...
Page 15
PWM comparator and PWM latch section Fig.9 shows the PWM comparator and latch section. The on- duration of output waveform coincides with the rising duration of CF terminal waveform,when the infinitive resistor is connected between F/B terminal and GND. When ...
Page 16
It is rather recommended to use not "CLM+" but "CLM-" terminal,as the influence from the gate drive current of MOS-FIT can be eliminated and wide voltage rating -4V is guaranteed for absolute maximum rating. There happen ...
Page 17
NO OPERATING DURATION 2V Fig.15 Waveform of CT terminal Fig.16 shows the Icc versus Vcc in this timer-off duration. In this duration the power is not supplied to IC from the third winding of transformer but through from the resistor ...
Page 18
Fig.20 shows how to connect the ON/OFF terminal.The switching operation will stop by swich-off and operate by switch- on. Transistor or photo transistor can be replaced by this switch,of course.No resistor 100k is connected and ON/OFF terminal ...
Page 19
Vcc 7.8V 8k 12k Q1 Q2 400 Q3 OVP 2. GND I1=0 when OVP operates Fig.22 Detail diagram of OVP circuit 8 OVP RESET POINT 8.82V(-30°C) 7 8.97V(25°C) 9.07V(85° Ta=-30°C Ta=25°C 4 Ta=85° ...
Page 20
It is not necessary that the induced voltage is settled higher than the operation start-up voltage Vcc (START) drive voltage causes high gate dissipation,on the other hand,too low gate drive voltage does not make the MOS-FET fully on- state or ...
Page 21
R1 Vcc M51995A CVcc1 CVcc2 GND Fig.27 DC source circuit for stable start-up OVP circuit (1)To avoid the miss operation of OVP It is recommended to connect the capacitor between OVP terminal and GND for avoiding the miss operation by ...
Page 22
Current limiting circuit (1)Peripheral circuit of CLM+,CLM- terminal Fig.31 and 32 show the example circuit diagrams around the CLM+ and CLM- terminal.It is required to connect the low pass filter,as the main current or drain current contains the spike current ...
Page 23
Under the condition of current limiting operation,the output current I2 continues as shown in Fig.33.So the output voltage depends on the product of the input primary voltage V on-duty. If the third winding polarity is positive ,the Vcc depends on ...
Page 24
M51995A OVP Fig.39 Application circuit diagram to keep the non-operating condition when over load current condition will continue for specified duration Output circuit (1)The output terminal characteristics at the Vcc voltage lower than the "Operation-stop" voltage V ...
Page 25
V OUT M51995A Fig.42 Output buffer circuit diagram DET Fig.43 shows how to use the DET circuit for the voltage detector and error amplifier. For the phase shift compensation,it is recommended to connected the CR network between det terminal and ...
Page 26
Vcc Vcc M51995A -Vss EMITTER GND (-2V to -5V) Fig.47 Driver circuit diagram (1) for bipolar transistor Driver circuit for bipolar transistor When the bipolar transistor is used instead of MOS-FIT,the base current of bipolar transistor must be sinked by ...
Page 27
APPLICATION EXAMPLE Feed forward types SMPS with multi-output FIN V OUT VF MITSUBISHI (Dig./Ana. INTERFACE) SWITCHING REGULATOR CONTROL R1 COLLECTOR Vcc M51995AP ON/OFF OFF M51995AP/FP ...