TZA3031BHL NXP Semiconductors, TZA3031BHL Datasheet
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TZA3031BHL
Related parts for TZA3031BHL
TZA3031BHL Summary of contents
Page 1
... DATA SHEET TZA3031AHL; TZA3031BHL; TZA3031U SDH/SONET STM1/OC3 laser drivers Product specification Supersedes data of 2000 Feb 22 INTEGRATED CIRCUITS 2002 Aug 13 ...
Page 2
... Digital-to-Analog Converter (DAC). The TZA3031BHL is provided with an additional RF data input to allow remote system testing (loop mode). The TZA3031U is a bare die version for use in compact laser module designs. The die contains 40 pads and features the combined functionality of the TZA3031AHL and the TZA3031BHL ...
Page 3
... CONTROL BLOCK 28 29 CURRENT MUX 19 SWITCH 20 BAND GAP REFERENCE TZA3031BHL 18 CC(R) V CC(G) V CC(B) ALS GND Fig.2 Block diagram of TZA3031BHL. 3 Product specification TZA3031AHL; TZA3031BHL; TZA3031U ALARMHI 18 2 MONIN 22 ONE 23 ZERO LAQ 15 BIAS 6 BGAP 11, 14, 16, 17 24, 25, 32 ...
Page 4
... Product specification TZA3031AHL; TZA3031BHL; TZA3031U DESCRIPTION ...
Page 5
... GND 2 GND 3 4 TZA3031AHL GND 8 Fig.3 Pin configuration of TZA3031AHL. 5 Product specification TZA3031AHL; TZA3031BHL; TZA3031U DESCRIPTION 24 GND 23 ZERO 22 ONE ALARMLO 21 V CC( CC(R) 18 ALARMHI 17 GND MBK846 ...
Page 6
... TONE TZERO BGAP V CC(G) FUNCTIONAL DESCRIPTION The TZA3031AHL, TZA3031BHL and TZA3031U laser drivers accept a 155 Mbits/s STM1 Non-Return to Zero (NRZ) input data stream, and generate an output signal with sufficient current to drive a solid state Fabry Perot (FP) or Distributed FeedBack (DFB) laser. They also contain dual loop control circuitry for stabilizing the true laser optical power levels representing logic 1 and logic 0 ...
Page 7
... The accuracy of the V and ZERO is described in Section “Accuracy of voltage on inputs: ONE, ZERO, ALARMLO, ALARMHI” MGS906 handbook, halfpage BIAS TR n MGS907 Fig.8 7 Product specification TZA3031AHL; TZA3031BHL; TZA3031U . CC(G) to pins ONE and ZERO CC(R) . The reference current applied CC(R) 1.5 V voltage at pins ONE CC(R) V CC( ...
Page 8
... A/W. E XAMPLE A laser with an MPD has the following specifications The term I the laser. If the laser operates just above the threshold level, it may be assumed that is 50% of decreasing near the threshold level. 8 TZA3031AHL; TZA3031BHL – --------------------- - TONE LASER 1 ...
Page 9
... TONE range from 1.4 to 3.4 V. Any connection to these pins should have a very high impedance value mandatory to use a CMOS buffer or an amplifier with an input impedance higher than 100 G and with an extremely low input leakage current (pA). 9 Product specification TZA3031AHL; TZA3031BHL; 3 (mA ...
Page 10
... Bias and modulation currents in excess of the specified range are not supported and should be avoided. Currents into or out of pins TZERO and TONE in excess must be avoided to prevent damage to the circuit. and , respectively. ZERO V CC(R) MGS911 10 Product specification TZA3031AHL; TZA3031BHL; TZA3031U ...
Page 11
... (typical device 125 C (typical device (device with characteristics at lower limit of manufacturing tolerance range). j Fig.12 Modulation current with variation in T 2002 Aug 13 TZA3031AHL; TZA3031BHL; 2.4 2.9 and tolerance range in the manufacturing process Product specification TZA3031U MGS904 (1) (2) ...
Page 12
... (typical device 125 C (typical device (device with characteristics at lower limit of manufacturing tolerance range). j Fig.13 Bias current with variation in T 2002 Aug 13 TZA3031AHL; TZA3031BHL; 2.4 2.9 and tolerance range in the manufacturing process Product specification TZA3031U MGS903 (1) (2) ...
Page 13
... This variation can be compensated for where devices in the application are individually trimmed. Temperature: The variation (middle of the specified range) the total variation in T <3%. 13 Product specification TZA3031AHL; TZA3031BHL; TZA3031U V CC(R) 20 ALARM 43 MGS909 GND Fig.14 ALARM output. ...
Page 14
... Upper limit of manufacturing tolerance range. (3) Nominal product. (4) Lower limit of manufacturing tolerance range. Fig. pins ONE, ZERO, ALARMLO and ALARMHI with variation in T ref 2002 Aug Product specification TZA3031AHL; TZA3031BHL; TZA3031U MGS901 (2) I ref = ( (4) (2) I ref = (3) ...
Page 15
... Note that the optical receiver used in conjunction with the TZA3031BHL must have a loop mode output in order to complete the test loop. The loop mode is selected by a HIGH level on pin ENL. ...
Page 16
... BIAS pins LA and LAQ pin ALS pins ONE and ZERO pins DIN and DINQ pin ALARM (TZA3031AHL) pins ALARMHI and ALARMLO (TZA3031AHL) pins DLOOP and DLOOPQ (TZA3031BHL) pin ENL (TZA3031BHL current on n pin MONIN pins TONE and TZERO pin BGAP ...
Page 17
... CC(G) I supply current (B) CC(B) I total supply current CC(tot) P total power dissipation tot Data inputs: pins DIN and DINQ (and pins DLOOP and DLOOPQ on TZA3031BHL); see Fig.17 V input voltage i(p-p) (peak-to-peak value) V input offset voltage IO V minimum input voltage I(min) ...
Page 18
... V ; CC(R) note 5 note 6 floating output note 7 floating output note 8 note 30mA o(mod)(on 60mA o(mod)(on) note 10 note 10 note 11 note mA; note 13 O(BIAS) 18 Product specification TZA3031AHL; TZA3031BHL; TZA3031U MIN. TYP. MAX 1 1.5 4 1.4 3 130 1.4 3.4 100 145 190 2.5 60 ...
Page 19
... V, and parameter processes are at a minimum. O(BIAS) is the on-chip dissipation when V tot , and parameter processes are at a maximum. O(BIAS with I O(BIAS o(mod)(on) 19 Product specification TZA3031AHL; TZA3031BHL; MIN. TYP. 6 100 1.5 200 315 400 7 1.5 1300 1600 1800 7 ...
Page 20
... The high-bias threshold range 97.5 mA. 15. See Section “Bias alarm for TZA3031AHL”. handbook, full pagewidth 2002 Aug 13 V I(max I(min) Fig.17 Logic level symbol definitions for data inputs. 20 Product specification TZA3031AHL; TZA3031BHL; TZA3031U and between CC(R) V CC(R) V i(p-p) MGK274 ...
Page 21
... ALS DINQ 7 10 19 TZA3031AHL 11, 14, 16, 17, 6 24, 25 GND BIAS MPD 21 Product specification TZA3031AHL; TZA3031BHL; DIN ALARM (5) ( ZERO 23 ONE 22 ALARMLO 21 ALARMHI 18 LAQ ( laser TZA3031U (6) (6) R4 MBK848 ...
Page 22
... R1 and R2 are used for setting optical 0 and optical 1 reference currents (see Section “Automatic laser control”). ( required for balancing the output stage (see Section “Power supply connections”). Fig.19 Application diagram showing the TZA3031BHL configured for 155 Mbits/s (STM1/OC3). 2002 Aug 13 ...
Page 23
... Note +910 +490 1. All x and y coordinates represent the position of the +910 +630 centre of the pad in m with respect to the centre of the die (see Fig.20). +681 +910 +541 +910 23 Product specification TZA3031AHL; TZA3031BHL; TZA3031U COORDINATES PAD x 23 +384 24 +227 25 + ...
Page 24
... TZA3031U Fig.20 Bonding pad locations of TZA3031U. 2 2.000 mm (4.000 Product specification TZA3031AHL; TZA3031BHL; TZA3031U 22 21 GND 20 GND 19 BIAS 18 GND ( LAQ 15 GND 14 V CC( CC(B) 12 GND MBK849 ...
Page 25
... 2.5 scale (1) ( 0.27 0.18 5.1 5.1 7.15 0.5 0.17 0.12 4.9 4.9 6.85 REFERENCES JEDEC EIAJ MS-026 25 TZA3031AHL; TZA3031BHL detail 7.15 0.75 1.0 0.2 0.12 0.1 6.85 0.45 EUROPEAN PROJECTION Product specification TZA3031U SOT401 (1) ( ...
Page 26
... To overcome these problems the double-wave soldering method was specifically developed. 2002 Aug 13 TZA3031AHL; TZA3031BHL; If wave soldering is used the following conditions must be observed for optimal results: Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave ...
Page 27
... Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2002 Aug 13 (1) not suitable not suitable suitable not recommended not recommended 27 Product specification TZA3031AHL; TZA3031BHL; TZA3031U SOLDERING METHOD WAVE REFLOW suitable (3) suitable suitable (4)(5) suitable ...
Page 28
... It is the responsibility of the customer to test and qualify their application in which the die is used. 28 Product specification TZA3031AHL; TZA3031BHL; TZA3031U DEFINITIONS Philips Semiconductors All die are tested and are guaranteed to ...
Page 29
... Philips Semiconductors SDH/SONET STM1/OC3 laser drivers 2002 Aug 13 TZA3031AHL; TZA3031BHL; NOTES 29 Product specification TZA3031U ...
Page 30
... Philips Semiconductors SDH/SONET STM1/OC3 laser drivers 2002 Aug 13 TZA3031AHL; TZA3031BHL; NOTES 30 Product specification TZA3031U ...
Page 31
... Philips Semiconductors SDH/SONET STM1/OC3 laser drivers 2002 Aug 13 TZA3031AHL; TZA3031BHL; NOTES 31 Product specification TZA3031U ...
Page 32
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2002 All rights are reserved. Reproduction in whole or in part is prohibited ...