AT24C02 ATMEL Corporation, AT24C02 Datasheet
AT24C02
Specifications of AT24C02
Available stocks
Related parts for AT24C02
AT24C02 Summary of contents
Page 1
... The AT24C01A/02/04/08A/16A is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini-MAP (MLP 2x3) (AT24C01A/AT24C02/AT24C04), 8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) versions. Table 1. Pin Configuration ...
Page 2
Absolute Maximum Ratings Operating Temperature..................................–55°C to +125°C Storage Temperature .....................................–65°C to +150°C Voltage on Any Pin with Respect to Ground .................................... –1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Figure 1. Block Diagram AT24C01A/02/04/08A/16A 2 ...
Page 3
... DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired for the AT24C01A and the AT24C02. As many as eight 1K/2K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). ...
Page 4
Table 3. Pin Capacitance Applicable over recommended operating range from T Symbol Test Condition C Input/Output Capacitance (SDA) I/O C Input Capacitance ( Note: 1. This parameter is characterized and is not 100% tested. Table ...
Page 5
Table 5. AC Characteristics Applicable over recommended operating range from TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High ...
Page 6
Device Operation AT24C01A/02/04/08A/16A 6 CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an exter- nal device. Data on the SDA pin may change only during SCL low time periods (see Figure 4 on page 7). Data ...
Page 7
Bus Timing Figure 2. SCL: Serial Clock, SDA: Serial Data I/O Write Cycle Timing Figure 3. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The write cycle time t is the time from a ...
Page 8
Figure 5. Start and Stop Definition Figure 6. Output Acknowledge AT24C01A/02/04/08A/16A 8 0180Z1–SEEPR–5/07 ...
Page 9
Device Addressing Write Operations 0180Z1–SEEPR–5/07 The 1K, 2K, 4K, 8K and 16K EEPROM devices all require an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 7). The ...
Page 10
ACKNOWLEDGE POLLING: Once the internally timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the ...
Page 11
Figure 7. Device Address Figure 8. Byte Write Figure 9. Page Write (* = DON’T CARE bit for 1K) 0180Z1–SEEPR–5/07 MSB 8K 16K 11 ...
Page 12
Figure 10. Current Address Read Figure 11. Random Read (* = DON’T CARE bit for 1K) Figure 12. Sequential Read AT24C01A/02/04/08A/16A 12 0180Z1–SEEPR–5/07 ...
Page 13
AT24C01A Ordering Information Ordering Code (2) AT24C01A-10PU-2.7 (2) AT24C01A-10PU-1.8 (2) AT24C01A-10SU-2.7 (2) AT24C01A-10SU-1.8 (2) AT24C01A-10TU-2.7 (2) AT24C01A-10TU-1.8 (2) AT24C01A-10TSU-1.8 (2) AT24C01AU3-10UU-1.8 (2) AT24C01AY1-10YU-1.8 (Not recommended for new design) (3) AT24C01AY6-10YH-1.8 (4) AT24C01A-W1.8-11 Notes: 1. This device is not recommended for ...
Page 14
... AT24C02-W2.7-11 Notes: 1. This device is not recommended for new design. Please refer to AT24C02B datasheet. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. 2. “U” designates Green Package + RoHS compliant. 3. Available in waffle pack and wafer form; order as SL719 for wafer form. Bumped die available upon request. Please contact Serial EEPROM Marketing ...
Page 15
AT24C04 Ordering Information Ordering Code (2) AT24C04-10PU-2.7 (2) AT24C04-10PU-1.8 (2) AT24C04N-10SU-2.7 (2) AT24C04N-10SU-1.8 (2) AT24C04-10TU-2.7 (2) AT24C04-10TU-1.8 (2) AT24C04Y1-10YU-1.8 (Not recommended for new design) (3) AT24C04Y6-10YH-1.8 (2) AT24C04-10TSU-1.8 (2) AT24C04U3-10UU-1.8 (4) AT24C04-W1.8-11 Notes: 1. For 2.7V devices used in the ...
Page 16
AT24C08A Ordering Information Ordering Code (2) AT24C08A-10PU-2.7 (2) AT24C08A-10PU-1.8 (2) AT24C08AN-10SU-2.7 (2) AT24C08AN-10SU-1.8 (2) AT24C08A-10TU-2.7 (2) AT24C08A-10TU-1.8 (2) AT24C08AY1-10YU-1.8 (Not recommended for new design) (3) AT24C08AY6-10YH-1.8 (2 AT24C08AU2-10UU-1.8 (4) AT24C08A-W1.8-11 Notes: 1. For 2.7V devices used in the 4.5V to ...
Page 17
AT24C16A Ordering Information Ordering Code (2) AT24C16A-10PU-2.7 (2) AT24C16A-10PU-1.8 (2) AT24C16AN-10SU-2.7 (2) AT24C16AN-10SU-1.8 (2) AT24C16A-10TU-2.7 (2) AT24C16A-10TU-1.8 (2) AT24C16AY1-10YU-1.8 (Not recommended for new design) (3) AT24C16AY6-10YH-1.8 (2) AT24C16AU2-10UU-1.8 (3) AT24C16A-W1.8-11 Notes: 1. This device is not recommended for new design. ...
Page 18
Packaging Information 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions A and L are measured ...
Page 19
JEDEC SOIC e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 0180Z1–SEEPR–5/07 1 ...
Page 20
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, ...
Page 21
MAP D E Top View Side View 2325 Orchard Parkway San Jose, CA 95131 R 0180Z1–SEEPR–5/ End View A SYMBOL TITLE 8Y1, 8-lead (4.90 x 3.00 mm ...
Page 22
Mini-MAP (MLP 2x3 mm) D Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm ...
Page 23
SOT23 E1 1 Seating Plane NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB, for additional information. 2. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, ...
Page 24
E Pin 1 Mark this corner D Top View Bottom View Notes: 1. These drawings are for general information only. No JEDEC Drawing to refer ...
Page 25
PIN 1 BALL PAD CORNER Top View PIN 1 BALL PAD CORNER 1 2 (d1 (e1) Bottom View 8 SOLDER BALLS 1. Dimension “b” is measured at the maximum solder ball diameter. This ...
Page 26
Revision History Doc. No. 0180Z1 AT24C01A/02/04/08A/16A 26 Date Comments 5/2007 Implemented revision history. Changed formatting on page 16 0180Z1–SEEPR–5/07 ...
Page 27
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Atmel Operations Memory ...