M62301FP MITSUBISHI, M62301FP Datasheet
M62301FP
Available stocks
Related parts for M62301FP
M62301FP Summary of contents
Page 1
... Vcc CURRENT CONTROL 0.49V 0.36V REF DISCHARGE DECODER INTEGRATING CAPACITOR GIRDLING 2 MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP, INT 16 5 RESET 6 15 GIRDLING INTEGRATING 8 13 CAPACITOR GIRDLING ANALOG GND ...
Page 2
... Note 1.Maximum analog input voltage is less than the difference between Vcc-2.5V as well REF *Charging current 10~12-BIT 4CH INTEGRATING A-D CONVERTER Conditions Min 4.5 4.5 0 =50µ 300 6 MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP Ratings 15 8 -0.3~VDD+0.3 -0.3~VDD+0 990(DIP)/660(FP) 9.9(DIP)/6.6(FP) -20 ~ +75 -55 ~ +125 Limits Typ Max 12.0 8 ...
Page 3
... REF C =4700pF REF (Note 1)R =24k I (Note 2)R =24k I V =2.5V,C =0.01µ =24k I V 8=3V 0.3V C =4700pF I I =1mA OL V 5=15V I =1mA OL V 5=15V VRE=5V R =2.2k ,V 0.4V L LRE R =100k ,V 0.4V L LRE MITSUBISHI ELECTRIC M62301SP,FP Limits Min. Typ. Max. 1.0 2.0 2.5 0 2.2 1.17 1.22 1.27 50 -10 0.1 0.05 0.02 0.09 526 3 17 -0.35 -3.5 3.5 0.8 0.1 0.4 1 4.45 4.60 4. 150 300 75 0.1 0 ...
Page 4
... Note. To ensure discharge from capacitor the above diagram should stay in mode 1 at least for the and REF period calculated above: Tdi=( not necessary to measure T channel. MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP, performed.None of these operations ...
Page 5
... RE 4.45V,the RESET output status becomes "L".If voltage increases over 4.50V,the RESET status becomes "H" within 150µsec. 10~12-BIT 4CH INTEGRATING A-D CONVERTER .............(2) 50mA 4.45V 0.8V OUTPUT UNSETTLED T DE MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP, REF 1.22V ...
Page 6
... I =50µ 24k R I 1.22V = . = . 50µA I 24k MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP C :To stabilize reference voltage, REF be sure to connect capacitance of approximately 4700pF. C :We suggest that this capacitance INT be connected to prevent malfunction due to noise. INPUT ANALOG VOLTAGE 4700pF Use C that leaks as slight current I as possible ...
Page 7
... V max+0. 1mA max is 5V. IA MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP, :To stabilize reference voltage, REF be sure to connect capacitance of approximately 4700pF. C :We suggest that this capacitance INT be connected to prevent malfunction due to noise. INPUT ANALOG VOLTAGE 4700pF Use CI that leaks as slight current as possible ...
Page 8
... INT OUTPUT CURRENT I 10~12-BIT 4CH INTEGRATING A-D CONVERTER 125 75 100 INT (mA) O MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP ANALOG PART SUPPLY CURRENT VS.SUPPLY VOLTAGE 2.0 1 ANALOG Vcc (V) LINEAR ERROR 0.05 0.04 0.03 0.02 RI=24k RI=12k 0.01 0 2.0 1.0 0 (OSR) ANALOG INPUT RANGE VIA(V) INT OUTPUT VS.AMBIENT TEMPERATURE ...
Page 9
... RESET VOLTAGE Vcc V (V) RE MITSUBISHI<Dig.Ana.INTERFACE> 10~12-BIT 4CH INTEGRATING A-D CONVERTER 4.7 4.6 4.5 4.4 4.3 4.2 10 -20 AMBIENT TEMPERATURE Ta(°C) DELAY TIME VS.AMBIENT TEMPERATURE 250 200 150 100 -20 AMBIENT TEMPERATURE Ta(°C) (mA) 2.0 MITSUBISHI ELECTRIC M62301SP,FP DETECTION VOLTAGE vs. AMBIENT TEMPERATURE ...